Search:

Thanks
Please see the new post.

Thanks
Please check our system
458142
458144

Thanks
when our machine were installed a man from machine maker connected to control and checked and edit the PMC control online by PC and Ladder software.
But I can not connect there are some...

I have Ladder III software . I cannot edit PMC program no communication between PC and control? ( Fanuc 18t Year 2000)
Which setting shouhd be set on machine?
Please help me.
Thanks

Hi
I am looking for a documents that I can define a New M code in our CNc machine with 840 C sinumerik.
Please help me
Thanks

we have a turning machine whit sinumerik 810 Ga1 ( or GA2 ???) which was stop for a long time . After reloading the PCP , TEA1 and TEA2 file and general rest the alarm 11 error UMS identifier...

hello
I want to connect ladder3 on Pc to Fanuc 21T (year 2000) which setting is nessesary ? which parameters should be change to establish connection tp Pc and I can see PMC program online?
thanks

Hello everybody!!

We have CNC center with Sinumerik 840C I want to add a measuring instrument to machine.

The instrument has a serial RS232 Output , is it possible to read serial port while NC...

Which documents (manual ) should I read about # in programming? I could not find in programming manual about # or programming to read and wrie Input or output of PMC.
Thanks

Thanks for your reply I AM LOOKING FOR cnc program instruction so I CAN READ pmc input and write to PMC OUT PUT
thanks

Thanks for your reply
I want to connect a barfeeder to our CNC machine is it possible to set an out put and read an Input of PMC in CNC program?

I want to write a new M code to set a PMC out put .
How can I do it ? which documents I should read?
thaks

We have CNC machine with Fanuc Om control the alarm 401 stops the machine according documents I have checked input voltage of axis drives but it is Ok
which part or parameter should be checked?...

We have acenter machine with Fanuc Om control . the alarm "401 Vrdy turn off" stops the machine.
machine may work for several sets but suddenly stoped by alarm 401 .I have checked input power of...

justb this simple program
N20 G00 G53 z-1
N30 M03 S1000
N40 G00 X120 Y100
M30

Thanks all for youe reply

my proram is:

N20 G00 G53 z-1
N30 M03 S1000
N40 G00 X.. Y..
N50 G01 F.. Z...

if I omit line N30 M03 S1000 the program executed normally! without problem and...

I have checked Spindle arrival signal it is "ON" after a few milisecond after M03 S1000 command.
but the program stop in this line!!?
Thanks

We have center machine with Fanuc OM control
I wrote a program such:

.
.
.
N50 G53 g00 z-10...
N60 M03 s1000
N70 ...

Hello
We have a lathe with Fanuc Oi mate But it cannot execute G76 threading .
we have defined all parameters of G76 acc to operating manual but the machine does not dothe threading step by step...

The axises now can travel in MPG or Jog mode but the errors remain
do you help me some fanuc documents about adjusting zero and refrencs in OM system?
Thanks

We have a CNC machine Tape drill OM system now have alarms
310: x axis need ZRN... 320: y axis need ZRN..
I dont know how:confused: :confused: I can remove the alarms
when I try to move the...

we have a machnine with OM system
how can we edit or load PMC program with FtapLadder software I need how to go to the loading menu?
what is the meaning of parameters p900 to 1000 it is not in the...

who has experiments with fanuc OM system
our machine have problem

We have CNC with fanuc OM controller all parameters have been lst and we have to enter all f them again is it possible to load them via rs232 serial port from a PC?
thanks:confused:

how dose has some information about fanuc 18T twin spindle control system?
I have a problem about sychronization of two spindle.
thank you