504,476 active members
3,214 visitors online
Register for free
Login

Search:

Type: Posts; User: mactec54

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 15 minute(s) ago.

  1. Replies
    24
    Views
    39

    Re: Usability of Encoder on DC Motor,

    Should work fine as long as your wiring and Encoder is setup in the software is correct, you will be good to go
  2. Replies
    24
    Views
    39

    Re: Usability of Encoder on DC Motor,

    If you have a reasonable Encoder and index pulse /Z pulse is not needed or used, it makes for a slow and jerk operation, the whole objective is to have a synchronized spindle and X axes to operate as...
  3. Replies
    42
    Views
    1,099

    Re: 110v VFD's. Any issues?

    On 120V supply you have to have a minimum of 20A to run a 1.5Kw Spindle 25A would be better, so your normal 120v outlet is only 15A so you are not going to successfully run even a 1.5Kw Spindle on it...
  4. Replies
    24
    Views
    39

    Re: Usability of Encoder on DC Motor,

    There is nothing to fix

    Acorn does not have a problem with anything to do with Encoder input, the Encoder only needs to be on the spindle it can of cause be on both but is not needed unless you...
  5. Re: Chinese 2.2kw water cooled spindle not turning when starting

    So you have not connected the Ground 4th Pin in your spindle, if you have to spin it by hand to start it is missing a Phase either wiring, or a problem with the spindle / VFD check the continuity of...
  6. Replies
    80
    Views
    247

    Re: Chinese 2.2kw spindle burned out?

    The Drive faults with a load Spindle attached, so if he removes the Spindle the drive will output when turned on and then can be measured at U V W
  7. Replies
    80
    Views
    247

    Re: Chinese 2.2kw spindle burned out?

    In his case he does not need to be connect to the spindle or the drive will fault out, he can then check it powered up as there will be no load to make it fault
  8. Replies
    80
    Views
    247

    Re: Chinese 2.2kw spindle burned out?

    Not successfully without problems, 50Hz and 60Hz motors yes it is possible but not 400Hz Spindles



    Your over current problem is a missing Phase from a damaged VFD Drive IGBT or Zener Diode,...
  9. Replies
    44
    Views
    84

    Re: Z-axis overshooting sometimes

    Other than better cable to start with, yes shorting is the main problem when using exposed foil or braid
  10. Replies
    24
    Views
    39

    Re: Usability of Encoder on DC Motor,

    If you are only working at Hobby level then anything can work even just a single index pulse, it just the control he is using has a requirement which has to be met or it will not work
  11. Replies
    24
    Views
    39

    Re: Usability of Encoder on DC Motor,

    Yes that will work fine as long as you have the right Encoder, a lot seem to be using this Encoder which is on the low side but seems to work with the Acorn Control Omron E6B2-CWZ1X, they can be had...
  12. Re: Chinese 2.2kw water cooled spindle not turning when starting

    Don't keep trying it, you will damage it if it is not already, you have a wiring problem, post some photos of how you have wired everything
  13. Replies
    80
    Views
    247

    Re: Chinese 2.2kw spindle burned out?

    That Braiding does not work and can not be used for your installation, it could make it worse, if your correct cable cost $100 I would be surprised, most is normally around $60

    I'm not sure why...
  14. Replies
    24
    Views
    39

    Re: Usability of Encoder on DC Motor,

    I'm not sure what your point is his Control has a requirement, and a low count Encoder like you describe is a waste of time, for anything to do with machining, the more PPR the reaction and...
  15. Replies
    24
    Views
    39

    Re: Usability of Encoder on DC Motor,

    The Encoder would be geared to the spindle the motor is unimportant

    Tt seems like you have a lot of replies but nobody though to see what is suitable for your control
  16. Replies
    80
    Views
    247

    Re: Chinese 2.2kw spindle burned out?

    You need to check the Parameters are correct

    This can mean more than one thing, this is ( 1 ) to try increase PD014=8 and see if it can get up to speed if not then it has a Phase problem

    This...
  17. Replies
    44
    Views
    84

    Re: Z-axis overshooting sometimes

    It sounds like you are almost there

    You don't want anything to do with the Bob and Mains Power Grounding

    As the Filter is the supply to the VFD Drive the Ground should go to the VFD Drive ...
  18. Replies
    5
    Views
    16

    Re: New Spindle drive Boxford V190 VMC

    Just like the FWD direction it has a Relay connected to S2 for reverse you need another active Relay that connects to S3

    So if you have 2 Relays on your Breakout board you need to get both working...
  19. Replies
    80
    Views
    247

    Re: Chinese 2.2kw spindle burned out?

    Yes those numbers don't make any sense they are normally around 1.3 to 1.7 all very close to the same
  20. Replies
    27
    Views
    130

    Re: Chinese Spindle Stalling.. better vfd?

    It could be a faulty Spindle from the start

    Your 20A single phase supply may be a little light, and No the VFD would only draw what it can from the supply, and will only trip the Breaker if there...
  21. Replies
    22
    Views
    39

    Re: Absolute encoders

    This is what you want to be looking at DMM | Technology Solutions | AC SERVO DRIVE | AC SERVO MOTOR | ROTARY ENCODER $1200 would be a little light depending on what size motors you need
  22. Replies
    22
    Views
    39

    Re: Absolute encoders

    No one said a machine with Absolute Encoders does not know where it is at all times, they do, :) the question was about machining Homing which can be control forced or just start from where ever your...
  23. Replies
    22
    Views
    39

    Re: Absolute encoders

    You should of brought stepper system with Encoders already, that close the loop in the stepper drive, or a Ac Servo system
  24. Replies
    22
    Views
    39

    Re: Absolute encoders

    You have some misconceptions with Encoders

    If an Encoder has many Bits wide positioning, it would be no good for anything ( 1 Bit 1024 ) that's 1024 PPR

    Absolute Encoders you have to Home just...
  25. Replies
    80
    Views
    247

    Re: Chinese 2.2kw spindle burned out?

    Where any Faults displayed on the VFD screen

    Did you recheck the Spindle pins reading this is what you have to do first
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4