Search:

DonKes · 12-29-2023, 10:55 PM

Are you slaving the second X axis?

If not, look it up.

Don

DonKes · 09-06-2020, 04:09 PM

Could you reveal the brand, supplier or Ebay seller of the product?

Don

DonKes · 08-03-2020, 05:08 PM

It Has to be right --- I saw it on the INTERNET !!!!!!!!!!!!!!!

Don

DonKes · 04-14-2019, 06:38 PM

Magnetic fields attract chips (which generate more magnetic fields).

Don

DonKes · 04-13-2019, 04:22 AM

I used 5% soluable oil and water in a Dyno I built out of a Chrysler fluid coupling unit ( like a torque converter with a manual clutch on the back of it) in about 1959. Probably had a lot of mist in...

DonKes · 11-01-2018, 04:23 PM

I would be sure that your Y axis span on the rollers are 4 feet or more.

Don

DonKes · 10-08-2018, 03:45 PM

About 43 years ago I shared equipment with a guy that had an old hand tracer mill that had an X and Y handle that the operator used trace a part. It was surplus from a high school from many years...

DonKes · 09-25-2018, 04:46 PM

Are these parts available at my local LEGO store?

Don

DonKes · 08-31-2018, 03:41 AM

Temporarily add another thick spoilboard if you need to get closer. Only you know what your mix of usages are.

Don

DonKes · 08-23-2018, 05:22 AM

Rotate the images in your computer before you send them to cnczone.

Don

DonKes · 08-22-2018, 04:28 PM

I can see that you are a tinkerer and builder for building sake, like me.

If I am wrong, please explain your purpose for building and your expected finished product and usage.

Don

DonKes · 04-17-2018, 03:04 PM

Now for a non-political answer !!!

Will it stop you from building your dream if it costs 10% more on 25% of your items?

Don

DonKes · 02-28-2018, 06:11 PM

Read the other conversions.

DonKes · 02-21-2018, 05:45 PM

You might consider a mini mill for the small one.

Don

DonKes · 02-13-2018, 05:50 AM

Will my printer do that?

Don

DonKes · 12-24-2017, 05:52 AM

I have a 8.9" tablet and a 11.6" convertable. The 8.9 is closer to 4:3, but it is still too little to use as a touch pad. Then I got the 11.6 and it is not much taller than the 8.9. It may work for...

DonKes · 12-22-2017, 05:07 PM

Size counts. What do you need?

Don

DonKes · 12-18-2017, 05:11 PM

Measure the run out and complain VIGEROUSLY !!!

Don

DonKes · 12-15-2017, 06:22 PM

Normally open switches need to wired in parallel.

Normally closed switches need to wired in series.

Did you change the wiring?

Don

DonKes · 12-13-2017, 06:15 AM

Don't forget that the epoxy will have a miniscus so you should have the dams wide enough to have it flat wider than you think you need.

Don't ask me how I know. You can guess.

Dib

DonKes · 11-17-2017, 04:24 PM

Mostly it is YOU that determines the accuracy, not the starting machine.

Choices, Choices, Choices

Don

DonKes · 11-12-2017, 03:24 PM

You can't teach people to fish with a very complicated bait setup.

YOu have to make it simple so they can set the hook very soon.

You can set the hook with them by letting them write a line of...

DonKes · 11-10-2017, 04:55 AM

A little compressor and a big tank.

Don

DonKes · 06-14-2017, 03:41 AM

I have this under a G0704

Search Results for concrete mixing at The Home Depot

Don

DonKes · 06-13-2017, 04:06 PM

A big drip tray over plywood.

Don

DonKes · 06-13-2017, 03:51 AM

That looks wimpy. I would go with the bottom tool box.

Don

DonKes · 06-08-2017, 03:13 AM

Warming is a 2 edge sword. Heat makes it cure quicker. I think some experiments in thinning VS complete curing is in order if the mfg can't tell you all about it.

Spreading it evenly helps a lot,...

DonKes · 06-05-2017, 04:21 PM

Sounds like they are not very proud of their prices.

Don

DonKes · 05-18-2017, 04:29 PM

Exactly what I did.

Don

DonKes · 05-18-2017, 04:27 AM

I used a square nut on my 0704, but I don't remember what size. It was rather large.

I chucked the nuts in the lathe and turned then down until they fit in the bottom of the slot.

Don

My IndustryArena Login

My IndustryArena Login

Search:

Search: Search took 0.01 seconds.

Thread: CNC router build X axis not in sync dual motor.

Thread: Z Axis Touch Plate Recommendations

Thread: I smoked my HY VFD a month ago. Here is what happened.

Thread: Why did my Hall effect switch trigger position changed

Thread: Somebody using soluble oil for mist cooling machining - no rust ? Mixture?

Thread: Designing an extremely large CNC machine

Thread: opinion?

Thread: Generic parametrised cnc machine design

Thread: Optimal Z Axis Height

Thread: work with what you got build

Thread: work with what you got build

Thread: Will new tariffs affect our hobby?

Thread: Chester Champion 20v Mill ( g0704) cnc options

Thread: Building two CNCs for hardwood/plywood and other one for metal

Thread: DIY Pen Plotter Project

Thread: UCCNC in Windows tablet?

Thread: CNC routers

Thread: LMS 5200 mini lathe spindle wobbling

Thread: Limit Switches work in NO but not in NC

Thread: Is self leveling epoxy a must?

Thread: Accuracy I can expect from a RF-45 or similar cnc conversion? Bang for $$ point?

Thread: Teaching CAD/CAM to the poor in The Philippines

Thread: Create a (quiet) jet of air blowing without a compressor?

Thread: Hmm what should i put my mini mill on? Table? Toolbox?

Thread: Hmm what should i put my mini mill on? Table? Toolbox?

Thread: Hmm what should i put my mini mill on? Table? Toolbox?

Thread: Ran into trouble using epoxy to level linear rails

Thread: Graham's Optimum BF20 Build

Thread: Hoss's G0704

Thread: Hoss's G0704

This website uses cookies