The rapping sound is the pneumatic pump for the hydraulic work clamps. This is located under the table at the back of the machine, opposite side to the gauge block.
Is there oil in the reservoir of...
Type: Posts; User: perfpro
The rapping sound is the pneumatic pump for the hydraulic work clamps. This is located under the table at the back of the machine, opposite side to the gauge block.
Is there oil in the reservoir of...
I was meaning for you to change - increase - character delay and line delay settings on your pc.
My machine transfers at 1200 baudrate, and that's okay for me. I do recall that we had some problems...
Check that Punch Code = 1:ISO on the 03P (MDI, SET, page02)
I have set termination string as G50.
7 databits, even parity, 1 stopbit, initialization %, termination G50
Try setting character delay...
My machine has parameter 02 set at 7000, and parameter 04 is 0004 as the only parameters altered when I installed the PAHIO serial port card.
Note when transferring programs DO NOT USE SIO on...
MDI mode Pattern/Shift key then Set gets to the parameters
The Vipros 357 is my choice.
The benefits of the PHNC hydraulic control makes for easier setup for marking, forming and embossing tools. The punch hover feature reduces run times on jobs.
I also...
Is the Velocity Control Unit on a hinged panel?
I had similar error on a Fanuc Tape Drill some years ago, was a blown fuse behind the velocity control unit panel.
I had S01 alarm 0032 on Mitsubishi M-V5B with Meldas M520MR.
Replaced the DK-517 sub-boards in the MDS-B-SP-75 spindle drive unit, and that has got machine working again.
I am curious as to why...
You need parameters for your machine, only some of the parameters from my machine will be applicable.
Here are the MMC parameters, they may be suitable for your machine.
I have 04P-C control on Amada Vipros 357, and similarly have experienced turning on the machine and finding many of the parameters have been cleared / reset to all zeros. First happened about eight...
You may need to initialize the memory, this will clear all the parameters and all stored programs. To do this you press and hold 0 (zero) and Delete keys while you power on. Then you reload the...
The A/I brakes should be on when the A/I station is not in use, so if the machine is switched off you should not be able to turn the A/I by hand. There would be proximity switches to indicate...
I have had a problem in the past with slugs jamming the A/I brake in the lower turret.
One option is to remove the centre cover plate from the top of the lower turret to clean away the scraps. ...
The relay board will be in the back of the electrical enclosure, the one with the main power on/off switch.
What control is it? 6M? O4PC?
Do the pins engage when you first turn on the controller, before the controller even boots up?
Check the relays, look for the one marked SHP.
I have changed the 'character delay' and 'line delay' settings on my DNC software to fix this problem. Increase these values to slow the transfer down a little.
I am not sure if this is because of...
Could be the flywheel hasn't stopped at Top Dead Center, if you have hit E-stop button during operation. You should have procedure for getting to Top Dead Center, in the operator's manual look for...
Good advice Mike.
Fabio1 be wary of overwriting existing machine parameters!
Load the tape as a program, as in O0001, then press Read.
The tape can be loaded as a program on another machine if...
You can read the tapes into the controller as a program, then save to your pc.
Is the 'Program Check' or 'Test' switch on?
When in 'auto' or 'memory' mode with program check 'on', the position display will change but the machine will not move.
Some machines can jog in manual...
RESET and DELETE only clears program memory.
CAN and DELETE clears parameters.
0 (number zero) and DELETE will clear all memory.
Has the machine been zero-returned?
After power up you need to zero-reference each axis.
The Fanuc controller alows you change a program number as it is read into the controller. Simply type address letter O and (up to} 4 digit program number, then press Read, (in either edit or auto...
Alarm 222 is software overtravel 'the +Y stored stroke limit has been overstepped'. What condition caused this? Programing error? Jog error while zero referencing?
Alarm 220 is 'the +Y stroke limit...
I suggest leave the G92 as the machine coordinates, G92 X79. Y50.
Use G98 to set the work coordinate 'offset'. G98 X... Y...
The G70 X absolute value must be greater than the repositioning travel ...
I would also check settings on the computer.
Why have different settings for input and output?
The jibberish file received at the pc indicates incorrect baud rate setting, at least it does with...
Sounds like tool change switch is on. See if the required tool is now at the tool change door. This is about 120 degrees CW from the striker.