584,841 active members*
4,467 visitors online*
Register for free
Login

Search:

Type: Posts; User: jaideepshinh

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    263

    Re: I 311 CCU Error number: 8412 hex

    Hi,
    Could you please share more information on your machine type? Is your the VMEbus type control or the MC/CCU control? Photos of your electrical panel would help determine this and the best...
  2. Re: HELP! Problem with C axis referencing on ITNC530

    Hi UGS,

    Have you solved your problem? If not, please look for a proximity sensor on the axis. In my machines, I have a proximity which tells the machine whether it had to reference forward or...
  3. Replies
    3
    Views
    876

    Re: Cincinnati Arrow 2

    Dear Tomaz,
    I hope you have a backup of your machine with you- or the original floppies/CDs available. This basically means your hard disk is busted. It is easy to replace, but you need the backup...
  4. Re: Cincinnati Arrow 1250C Convert from linear scale to servo motor encoder

    Hi Davekensco,

    You should be able to easily get used scales to replace your broken one. I do not recommend switching to encoder feedback as there are no reference switches in machines where scales...
  5. Re: Heidenhain TOS machine with relay error

    Hi,
    Are you familiar with the general operation of Heidenhain controls? Based on this we here would be able to guide you on the way forward.

    Relay ext. DC voltage missing isn't actually an error....
  6. Replies
    8
    Views
    1,891

    Re: Increase memory - Acramatic A2100

    Hi, I have retrofitted by A2100s with 828Ds and have the full system in spare. Mine had an option wherein I could execute much larger programs and a good amount of storage as well, and it had a...
  7. Re: Deckel Maho DMG 635V Spindle in not locking Well, Restart when spindle start rota

    Hi is your machine with Heidenhain drives or Siemens drives?

    I suggest changing your spindle drive and seeing if it works
  8. Replies
    2
    Views
    1,454

    Re: DMC 63V MMC 102 back up

    Dear Kochev

    MMC102 is the basic operating part of the system software- what is the reason you need the backup? Has your machine hard disk crashed?

    If yes, you can load it from any machine and...
  9. Re: Dmg dmu125 error c380 motor Z not controllable

    Hi Pribicevic,

    Were you able to solve your issue? This can happen for the following reasons:
    1. Change in motor phase sequence during replacement
    2. Mechanical jam- if the axis has hit a dead...
  10. Re: Who has installed a 3rd party 4th Axis and lived to tell the tale?

    Dear Craig,

    Yes thats true, but their quality is probably the best you can get in the market. And assuming there is wear out, they have it well documented as to how to adjust the backlash by...
  11. Re: Who has installed a 3rd party 4th Axis and lived to tell the tale?

    Ho Boydage

    There are quite a few Tsudakoma units available on ebay- you could try buying one of these are these are some of the best you can get. There are some unused pieces as well- make an...
  12. Replies
    6
    Views
    2,484

    Re: DECKEL 100V Gear at wrong position.

    Good! Best of luck!
  13. Replies
    6
    Views
    2,484

    Re: DECKEL 100V Gear at wrong position.

    Hi,
    The spindle on your machine has a star delta changeover contactor (You will notice two large contactors at the bottom left the simodrive units in your electrical panel). One contactor is on from...
  14. Replies
    4
    Views
    1,214

    Re: Heidenhain MC 420

    Hi,

    You can reuse the motors, encoders etc. Drives and IO boards etc would be useless. If I remember correctly, Siemens controls can run these motors as they have the parameters for these motors...
  15. Replies
    4
    Views
    1,214

    Re: Heidenhain MC 420

    Hi,

    Do you have the manuals of the machine available with you? Which control software was there? (CNC pilot or Manual Plus?). Have you received any CD along with the machine containing the machine...
  16. Re: Heidenhain LE2500B board ID Numbers Bridgeport 720x

    Hi Andy,

    Congrats on the progress!

    Yes for the reference issue, the logic works like this-
    1. Move axis towards limit
    2. Once limit is touched, reverse direction and look for encoder Z...
  17. Re: Heidenhain LE2500B board ID Numbers Bridgeport 720x

    Hi Andy,

    Definition of error Gross Positioning Error (Axis name, X in this case) C-

    Movement Monitoring
    - The voltage difference calculated by the control has reached the limit programmed in...
  18. Re: Heidenhain LE2500B board ID Numbers Bridgeport 720x

    Hi Andy,

    Just to check, is your position feedback to the control via scale or via motor encoder? How does the Servo drive take the feedback from the motor?

    I have seen the following...
  19. Re: Hiwin linear rail block initial lubrication procedure

    I have never seen these come without boxes! :nono:

    Good that its working better now.

    There is a lot of "tuning" to be done when dialing these, even if its against a precision reference surface....
  20. Re: Siemens SINUMERIC 810D transfer data problem

    You can connect the machine via ethernet. we have our 810D machines with PCU20 all connected via ethernet which is much easier to manage than RS232.

    Only drawback- you need a Windows XP system...
  21. Re: Hiwin linear rail block initial lubrication procedure

    Hi Steve,

    We do many linear rail installations in house (we recondition our own machines every now and then).

    You should be concerned if the block feels rough. The difference in feel between...
  22. Re: Heidenhain LE2500B board ID Numbers Bridgeport 720x

    Hi Andy,

    Please see attached the photos of the two controllers from the technical manuals. They look the same to me- but maybe I am mistaken. The only difference i can find is in the connection to...
  23. Replies
    2
    Views
    1,579

    Re: TS 641 Repair/Parts

    D_Turner,

    Did you manage to get your TS unit working? If yes how did you manage this? I have a similar unit needing attention at the moment!

    Best regards

    Jaideep
  24. Re: Can I control a Fanuc servo drive with 3rd party controller?

    Dear Mike,

    I would suggest looking for a used main board on ebay/other sources. It should be cheaper and less time consuming than swapping out the controller for a replacement lower cost one. Do...
  25. Re: Dmg dmu125 error c380 motor Z not controllable

    Hi,

    Is yours a DMU125P?

    Could you compare the motor part number of the original motor which was with the machine and the new motor? This can happen if the motor type number changes. If the type...
  26. Re: Heidenhain LE2500B board ID Numbers Bridgeport 720x

    Dear Andy,

    I am not sure if I am right about this, but the LE2500B looks the same as a TNC 355 to me. Heidenhain does this sometimes wherein it changes the labels for different manufacturers (I...
  27. Thread: DMU125P

    by jaideepshinh
    Replies
    1
    Views
    1,524

    Re: DMU125P

    Hi Baronas,

    Were you able to solve this issue?

    Also do you have the machine backup available for your machine? Would it be possible for you to share this with me? As well as a photo of the...
  28. Replies
    0
    Views
    1,391

    Default DMU125P System backup

    Hi!

    Does anyone have the backup for a DMU 125P 5 axis machine? I have purchased a machine recently (1998 model) which has a Philips mill plus control. The machine is operational but its the only...
  29. Replies
    2
    Views
    2,686

    Re: Fagor 800 T Error 99 M table

    Hi,

    I have an 8025T where I am having the same error- Error 99 Parity Ms. Is this relating to the PLC? Do we need to restore it from the EEPROM? I am unable to find much information on this...
  30. Re: DMC 60 H hi-dyn, 840D ~ MSG ... M00 causes error '600607: SPI-LK,feed stop'

    600607: SPI-LK,feed stop is a standard DMG code in their Siemens controllers which basically means the Spindle Locked Feed Stop is active. There is an interlock causing this. You can check the status...
Results 1 to 30 of 102
Page 1 of 4 1 2 3 4