Search:

Hello

As long as your write your programs in DIN then the programs are interchangeable. However every manufacturer has its own preferences regarding H-words and M-command. However that can be...

Hello Adisson
It been a long time for me too but as far as I know you have to go to Parameter -> display and first set the graphic parameter. Somewhere there should be N70.

Regard
Michael

Hello

I think it would be useful if you participate on a trainings course.. your new firm might help you to find a suitable course.. I mean it’s useful for them too to have a worker that knows...

Hello CTX 500
As far as I know the EPL 2.2 is only the last stage of this controller. Afterwards the EP controllers followed. So it's perfectly normal that you can only find the name EPL here in...

Hello
have you tried it with G0 Z1=100 X1=100?
Depending on the configuration, the C axis sometimes demands that.
Or try switching the G54 with G59..


Regards
Michael

@ 2312
Please share your experiences!
What exactly don’t you like about it? Controller too long-winded? Machine unstable? Bad service?

Regards
Michael

Hello Claudio

There is no overall answer to your question. For single part processing or small series, I am sure these machines are fine. You can save additional machines and you can be sure that...

Hello Spindler
The command should not be misused for the circular programming.
It only exists to chamfer- to create a tangential crossover- It replaced the old command B+ ..
In the following...

Hello FeLe4
It depends on the forging process but normally the outer layer is quite hard. Afterwards it gets better. For large scale productions, it worth considering taking oil for the cooling...

Hello Kerschkas!

Let's make it short and sweet: forget it!

The wear of the glass occurs mainly due to the bouncing chips that you already described. A foil would not do anything. Three years is...

Hello ste836!

You only have a chance to exert influence with the hand wheel, if the revolver is set up as NC axis by the manufacturer.
If it is a simple electronic revolver, then the revolver...

Hello and welcome in the forum!
Something went wrong here, what cycle do you mean?

Regards
Michael

Hello Schradm!

Have you ever tried it with a second zero offset?
The distance between revolver and tool should be visible in your machine specification sheet.

You just must not forget to...

Hello
Thank you for the quick answer. I already talked with SKF on the phone.
I research it over the internet but SKF only sells the complete unit and Mikron doesn’t tell me the performance data....

Hello Mayday !

I’m afraid to say that I don’t think that will work like you planned it. You can only do adaptations at the same time that have similar characteristics. So cut-in with quite low...

Hello Mayday !

I’m afraid to say that I don’t think that will work like you planned it. You can only do adaptations at the same time that have similar characteristics. So cut-in with quite low...

Hello Mayday !

I’m afraid to say that I don’t think that will work like you planned it. You can only do adaptations at the same time that have similar characteristics. So cut-in with quite low...

Hello Martillo!

An operating hour’s counter should be available on every machine. Regarding the cycle time, each manufacturer handles it differently. Some don’t do anything, in that case you have...

Hello

It’s possible to span the belt too much. When the belt is spanned you should be able to press it with one finger.
Have you checked that the belt pulleys run towards each other? If your...

Hello John
Try to get rid of the ! - then it should work. Otherwise you need to have a look how the manufacturer names the axes.
Generally about the word BRISK: It all goes a lot faster but it...

Hello
I don’t know the machine or the controller but have a look here:

http://www.stylehightech.com/index.php?i=sw

The controller looks very simple…

Regards Michael

Hello Digaa!

You can find Information about TRANSMIT in the Siemens automation manual chapter 7.8
( you can see it on the website www.automation.siemens.com)
But when its about NPVs then maybe...

If you can get a EPL2. In comparison with the EPL1, the EPL2 has a cutting radius comoensation. However you can’t expect the same comfort and speed from these old control systems.

If I remember...

For hard turning I would recommend you plates from Sumitomo. They have 15 different types of CNB so more than double than normal competitors. As you can cut the plates from all sides, so their...

Try it here:

http://www.plctalk.net/qanda/showpost.php?...amp;postcount=8

It’s a DOS based version 4.2

regards

Michael

Hello Steff
The 840 C was a good controller during its high season but since the end of the 90s, only the 840D is sold. That means that there were no further developments!
What the machine can do...

Hey Masi
It should work G17. Then it’s the milling layer.
About your second question: After the turning – spindle stop with M5. Afterwards Spos1=0 and then Spos1=20. You have to add a squared...

Hello Adrian,

You should have a look if the machine manufacturer has provided ‘’sealing air’ for the Glass scale. If not the next problem is predictable.

It might be worth thinking about...

Hello Tomdar,

Have a look at the pump. There is often a membrane located. After a long time it would be no wonder if it’s defect. Usually it’s enough to just replace this membrane.
If your...

With Siemens you always have to write a new blade by hand. To be honest I don’t know if it’s the same with Heidenhain or Fanuc.
Regards
Michael