584,830 active members*
5,881 visitors online*
Register for free
Login

Search:

Type: Posts; User: Chopdr230

Search: Search took 0.00 seconds.

  1. I know the original post is ten years old but I’m...

    I know the original post is ten years old but I’m in the process of setting up a chnc iii with a bison chuck . I can’t find any info . Can I cap the air lines to the collet closer and turn off a...
  2. Wanted Miyano tsv-35 parts or parts machine

    Looking for tool changer parts or an entire parts machine . Miyano tsv-35 . Bt40 taper . Probably a long shot but thought I’d give it a try . Thanks
  3. Fanuc om-c ladder diagram ( trying to get DNC )

    I have a mill with fanuc om-c . I would like to activate the DNC function . The machine dose not have a tape mode switch or any switches in the cabinet to activate it . There dose not appear to be a...
  4. Replies
    7
    Views
    5,188

    Re: Nomura NN13 lathe questions?

    im trying to figure out how to program this machine by following the program manual . my problem is I didn't have the O9801start position program . some nice people on here gave me there copy off...
  5. Replies
    7
    Views
    5,188

    Re: Nomura NN13 lathe questions?

    alloy craft I was in the same boat . my machine came with a dead battery . google translator worked wonders and its free
  6. Replies
    7
    Views
    5,188

    Would either of you happen to have the setup...

    Would either of you happen to have the setup program and O9801 macro the nomura program manual calls out ? I recently got a NN13 with a dead battery and had to reload everything . I’m new to Swiss...
  7. Replies
    3
    Views
    5,805

    Any Nomura users ? Looking for a macro

    I have a nn-13s I’m looking for the macro O9801 used with the setup program .
  8. Replies
    1
    Views
    657

    Meldas 64 fo page blank

    When I press the fo button the page is blank. I’m trying to get to the tool position base page .
  9. Replies
    1
    Views
    707

    Meldas 500 soft limits not responding

    I have a nomura lathe with the meldas control . When ever I try to home it out the y axis hits the emergency stop and kills the machine. I tried to adjust the soft limits but nothing works. Could it...
  10. Replies
    1
    Views
    708

    Meldas 64 feed Hold alarm

    I’m getting a feed hold alarm (212 support no act ) on my nomura lathe with a meldas 64 control. I tried to look up the alarm but it’s not in my book ? I can jog x and z but y is dead . No other...
  11. can you use a bigger drive for a ac servo

    I have a 1kw delta ac servo drive and a .75 kw delta motor . will the drive only put out what the motor draws ? or will i burn up the motor . can you mix and match drives and motors ? i know in a...
  12. How to go about getting om-c ladder edited for dnc function

    Hi i have a miyano tsv-35 and it dose not have tape or dnc modes , no switches on the control . I am able to see the ladder and searched for g127.5 and its not there . Is it possible to have it added...
  13. Replies
    1
    Views
    1,202

    Re: Miyano TSV-35 Spindle Bearing Lubrication

    Hi my name is AL I picked up a tsv-35 that needed some help . I have spent the last two months trying to get it up and running. I had to replace the power supply and crt wit a lcd . I’m still having...
  14. Replies
    3
    Views
    825

    Al I need your help also!! My name is also AL . I...

    Al I need your help also!! My name is also AL . I can’t get the website to work properly on my phone. That’s not my issue but that’s why I can’t contact you. I have a Fanuc on question....
  15. Miyano TSv-35l fanuc o-m . Z stuck in tool change position

    This machine is new to me . I put the atc in manual and zeroth to its full upward travel. I got a tool alarm 22 . Now z won’t move in any mode and I can not home the machine . I have the parameters...
Results 1 to 15 of 15