Search:

Yes this is true with some of Haas spindles.

To see if your machine has a serviceable draw bar you will need to provide you HFO or Haas factory with the machines serial number and they will have...

Happy to help you keep your chips flying.

Don't know if this helps at all but the password my be set by the machine dealer so you call them for service. I would definitely try the default one from the manual. The dealer we got are machine...

If you have not figured it out by now. But if you press cycle hold then press the "t" key then you can jog and stop the spindle. Where your done jog the tool close to where it was when you stopped it...

I was given a post for mastercam X6 from the machine dealer when we got are new lathe with has a fagor 8055T control.
was wondering where i put the three files for the post to work. also is there...

hi all
i am trying to set up dnc to may fagor 8055 lathe using a Ethernet connection. cant seem to figure it out. any help would be grate. i am using a computer with win7 if that makes a difference....

Hi all
I am trying to get my M10 subroutine to be activated by a unused botton on my 8055 control. Found the sub and it sub50 and the botton I want to use is B27 R562.

Any help would be grate
...

why not use usb??
if its a mill control then it needs to be .pim extion
if you dont have a usb on the control there is one inside of it that u can plug an egtention cord to. i find the usb to be...

630 x 2000mm Flat Bed CNC lathe

Model DMTG CKE61632
Control Fagor 8055 TC
Max swing 630mm (24.8")
Max swing over slide 320mm (12.59")
Width of bed 550mm (21.65")
Spindle nose C-11
Spindle...

When you r in that screen if you have the corsair on the "select a program" side (lefthand column) then press the recall key it should open the root screen. In this screen you can veiw and move...

Did your operator delete it form just your memory ( all your machine or did he delete it from the hard disk as well?

The subroutine should he backed up in the hard drive. If it is not backed up...

Hello all,
I have search all over the forms to only find a milling posts that dont work.

I would greatly appreciate if anyone could send me a working post for mastercam V8.

[email protected]
...

I have a 20 T flat bed lathe with a 4 post tool rest and with that machine I have to manually move the tool post with an alien key with the machine off.

Don't know if that helps any as I am not...

Not sure why the the turret is not moving. If the turret has released it should rotate. I would start with looking at the wires for any broken or lose wires. Also is the amplifier showing and...

Once you have replaced the batteries you will then have to re orientate the tool turret. Usually you can find the instructions on how to do this in the machine builder manual. If not then try...

Every time my machine gives this alarm it because of a low battery. There should be one in the tool change amplifier, main slide amp, and if you have live tooling there will be one for the spindle...

i had the amplifier burn out on the machine where the low voltage crossed the high voltage side (not a good day).
i had a tech replaced the amp and the servo motor and on start up he pressed delete...

have you checked the drive motor for heat? is that setup a derct drive or belt setup?
also for the x slide i would check the trust in the ball screw bearings

i opened that program and this is what i found:

%,MX--,
;(PRGSCRIPT 1)
;(DEBUG)
;[STDCONV]
;(WGDWIN 255)
;(AUTOREFRESH W1=PLCR185)
;(AUTOREFRESH W2=PLCR186)
;(AUTOREFRESH W3=PLCR702)

Hello all

we have just got a new lathe in the shop with the fagor 8055i. All the other lathes have a fanuc control on them, so all my programes have been posted from mastercam V8.

So I would...

what do i do this link is for downloads?? all i need to know is how to switch on the load metters

thanks

When i go into the machines general parameters and find P127 it has 65255 in the value column.

What do i need to to do to activate the loud metters??

have u had any luck with getting a post to work?? i just got a fagor 8055 and was woundering if you would be willing to send me a copy of the mastercam post?

Thanks

Hello to all.

I am new to fagor controls (been a FANUC user tell now). We just got a new lathe and it came with a fagor 8055 on it. So fare i like the control and I have been using it on the...

thanks for the info.

thanks for the link but that is not what i am looking for. i reailzes what the alarm is and i found the info to be very limited from that link. thanks for the reply any other help to figure out how...

hi there,
I have the same problem.
I was woundering if you have fix the problem?


When i cheack the help screens it shows a green dot at the home search had been done.

We just got the lathe...

i am upgrading my big lathe and i was looking at the haas st-40l.
just thought i would see what everyone's opinion is on it

Thanks for looking
:cheers:

i don't have the OT manual only have a Oi and i find it confusing as hell to understand it. its almost wrighten as if you now how to fully use the control already. just finishing the operation in the...

thanks for the info.
i will go give it a go and see how it works