Search:

Pre setter "speed" is controlled by the middle valve in the valve stack. Between the Chuck pressure and Tailstock pressure valves. Bottom left side of the front of the machine. On some years, the pre...

Chunk of perforated metal and a couple of magnets.

I left you a reply on the OneCNC forum.

Port #2 is for auxiliary axis communications.
Say a rotary axis driven thru a stand along box.
I don't think you can use it for loading / unloading / DNC to the main control.

You can just add the .050 to your work offset Z value..

So if you are using say G54, add .05 to the z value in the work offset table.

Here is warn up program. (O12020 Below)

Also a shot of the IO board. I just unplugged the door switch from P8. And jumped it as shown with common computer jumper.

This is on a 2000 mini...

Sure..need any more let me know.

Part #64-1447

Depends on if you want to cut it with a Tapered mill. Or use a Ball mill and step down the face.

Also if you have a 3 axis or 5 axis machine.

Gary,

Most likely , you will to do a delete "ALL" to clear the bad program.
This entails doing a download of all programs. Either one at time or with the "ALL" function into a single "ALL" file....

Phil,

My Fanuc use a decimal point for dwells. IE: 1.5, 2.0

If I used 2000 that would be 2000 seconds. Which would be 33.33 minutes..

Might try a P2.0

One note: mine use a X1.5 not P1.5...

Might be of some help.

You have mail.

Joe,

"CD Key " is not your serial number or Dongle number.

It is a a number to tell it what version to install..Express, Pro, Expert, etc.

After install it will ask for your dongle number...

N22 Z-4.725 (profile end)
G40 G00 X2.500
Z0.100
G96 S250
G70 P10 Q21 (finish pass) (Try Changing the Q21 to Q22)

Ken,

As far as I know, they are all the same..key"C101".

So any guy with a Haas machine can help you out..Even Vern. :stickpoke

I have spares..call me and I'll send you one, if the dealer...

Joe,

After you enter a section on the forum, (IE: XR6). You will see at the top of the page a "NEW" tab..click that..then "Discusion".

Ash,

I get 12 seconds here with your example settings.

That is with the default post.

You sure you don't have a second finish pass set ??

You could post your sample file to look at.

You need to set the "remove amount" and the "stepover" in the profile dialog to do what you are asking.. Then set the depth to full cut .

If need be, you can post your sample file here. And we can...

email:[email protected]


Phone: 909-931-7811

Sean,

You have "Advantage". It does not have any Solid modeling.

So I don't believe you ever did have "Extrude".

Sean,

A screen shot would help. But do you see a faint "home" icon at the top of the left hand menu?? If so, click that to get back to the main menu with the extrude icon on it.

No real way to...

I show some differences in parameter setting between a HRT7 and A HRT160. Like ratio steps. Plus might be others.

I'd call Haas Rotary before I plugged it in and had a go. Better safe than sorry....

The tool release piston could be sticking. I have in the past, fixed this by pouring about 10cc of WC40 in the air line going to the piston. (The two clear lines, one small and one large, in the back...

Parameter #52 is the fuse level for rotary axis (A).

Might check to see what that is set at..different rotaries are set to different levels.

Change at your own risk. But I have bumped it up a...

Glad to help and glad you got it worked out. :wave:

Quick fix listed below.

N100 G00 X1.60 Z.050;
N110 G00 X0.0................. (Remove this line)
(TURN TO DIA.)
N120 G71 U.050 R.100;
N130 G71 P140 Q190 U.050 W.050 F.020;
N140 G01 X0.0...

Z,

Sorry I didn't think of this before . Just set your field width to 4 and you are good to go.

That will got to N9999 then restart at N1.

Reposted this on the OneCNC forum too..

On some Haas' the beeper/speaker cover actually turns to change the volume..Kind of like the air vent on the dash of your car. might try that.

Guys,

Setting up your post to output a G13/G14 operation is rather simple.

In fact there are post on the OneCNC forum already set up to do this. Haas for example. But others are easy to do...