502,816 active members
4,509 visitors online
Register for free
Login

Search:

Type: Posts; User: xjdubber

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: Taiwan - SYNTEC - 6MB or 6MA - Controller Discussions

    Your right that where grease,waylube, or timed injection is a better option.
  2. Re: Taiwan - SYNTEC - 6MB or 6MA - Controller Discussions

    RIO = Remote IO instead of the IO being wired in some fashion directly from the controller it is networked trough a communications protocol to a remote location.
  3. Re: Taiwan - SYNTEC - 6MB or 6MA - Controller Discussions

    The balls will circulate trough the linear block, so I don't think its an issue where the oil and or grease is as it will circulate trough the block. When I worked for a Multicam distributor they...
  4. Re: Taiwan - SYNTEC - 6MB or 6MA - Controller Discussions

    Hi SyntecEngineer,

    I looked at serum's tool change macro, the one from the machine is about 2 to 3 pages longer, has some comments in english and some in chinese (i guess) hard to follow. What i...
  5. Re: Taiwan - SYNTEC - 6MB or 6MA - Controller Discussions

    Ok so now I've got a little bit to go trough, I think I know the screen that serum is talking about but when i set my xyz coordinates there they do not work in the coordinates used in the macro. I...
  6. Re: Taiwan - SYNTEC - 6MB or 6MA - Controller Discussions

    Hi all

    Im trying to find out how to change coordinate variables on the Syntec control. Im sorting out some issues on a omni router with and 11mb control on it. The tool height sensor location was...
  7. Replies
    2
    Views
    7

    Re: OMNI with Syntec 11MB

    HI Gfacer2,

    This is not displayed in the parameters screen, it is in the Global coordinates part of the diagnose screen and not editable in that screen, as far as i can tell. The password is the...
  8. Thread: Hi all!

    by xjdubber
    Replies
    1
    Views
    5

    Re: Hi all!

    looks like your message was meant to reply to someone but your started a new thread.

    Im trying to find how to change coordinate variables on and 11MB control, any suggestions? I need to change the...
  9. Replies
    2
    Views
    7

    OMNI with Syntec 11MB

    Hi all,


    Working on an omni router with syntec 11MB. the X,Y setting for the tool lenght sensor is off center a bit. The X,Y coordinates are held in variables 26061 and 26062. How does one edit...
  10. Replies
    5
    Views
    634

    Re: Holding down Styrene sheets

    If your wanting to do this cheaply..... what 1 shopvac wont hold down 2 or 4 might hold down. I think there is even someone out there that sells a setup with 4 vacuum/shopvac motors for this purpose.
  11. Thread: analog input

    by xjdubber
    Replies
    7
    Views
    1,546

    Re: analog input

    you'll need to check into the encoder connections of the motor to see if it will be compatible with the drive.
  12. Thread: analog input

    by xjdubber
    Replies
    7
    Views
    1,546

    Re: analog input

    Still need to add a motor to that to at that point, or do you have one already? Take a look at ADVANCED Motion Controls Servo Drives Brush Brushless Motor
  13. Thread: analog input

    by xjdubber
    Replies
    7
    Views
    1,546

    Re: analog input

    Ah, Now that i see where the message is actually posted.... sorry about that.

    They have step + direction drives only. Not sure if there is a converter to go from volts to step and dir. why not get...
  14. Thread: analog input

    by xjdubber
    Replies
    7
    Views
    1,546

    Re: analog input

    what drive? most servo drives take a 10v bipolar signal.
  15. Re: have an issue with obtaining 380 volts please help!!!

    MAT - Three Phase Auto Wound | Marcus Transformers

    these are auto transformers which are the cheapest you can get, and not isolation. select your input voltage as 230V and output as 380 and set...
  16. Re: have an issue with obtaining 380 volts please help!!!

    No you don't "need" an isolation transformer, however on cnc equipment it is desirable as your input voltage will be a lot cleaner. Your problem is that in north america 380v transformers are hard to...
  17. Re: have an issue with obtaining 380 volts please help!!!

    I'd get some more qoutes, the price on that transformer seems quite high for that transformer. You should get a full isolation transformer, would be better for the machine.
  18. Replies
    7
    Views
    826

    Re: Basic Controller Connections

    direction or DIR should reverse the motor direction DIR - must be referenced to power supply negative (all - signals must be) when providing a pulsing signal to PUL+ and no signal to DIR + the motor...
  19. Replies
    7
    Views
    826

    Re: Basic Controller Connections

    These connections you list are step and direction signals and cannot be used for manual up/down or fwd/up functions. this functionality will have to be setup trough extra inputs and the software you...
  20. Re: Import vise- Kurt soft jaws will not work

    Maybe you should try measuring in MM, as you said "import vise" 25 x 100 sounds like a pretty close measurement....
  21. Replies
    3
    Views
    384

    Re: Udisk Help required plz

    Try a memory stick with 1GB or less capacity, if needed a memory stick can be resized search google for this.
  22. Re: Need a replacment belt? Looking for a part. Help please

    Star linear was bought by bosch rexroth, should be able to contact your local bosch rexroth office to get part numbers and replacments
  23. Replies
    6
    Views
    2,542

    Re: Milltronics controller and Windows 10.

    and do this ....

    "To disable password-protected sharing (not recommended), go to Control Panel > Network and Sharing Center > Change advanced sharing settings > All Networks > Password-protected...
  24. Replies
    6
    Views
    2,542

    Re: Milltronics controller and Windows 10.

    Why would they have too have a windows 10 computer there? Just because you jumped on the bandwagon does not mean that everyone else has too. There are very valid reasons not have windows 10 in a...
  25. Replies
    15
    Views
    740

    Re: unintended opto output during boot

    He or they obviously do not have much experience building a proper control system. No matter whether its a metal spinner or a conveyor E-stop circuits need to be done properly. Metal spinners.... yup...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4