584,846 active members*
3,953 visitors online*
Register for free
Login

Search:

Type: Posts; User: machinehop5

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds; generated 14 minute(s) ago.

  1. Replies
    1
    Views
    29

    Re: Looking at a Tree 2UVR

    ...Welcome Duane,

    nice this machine has the knee(W axis) power feed motor......there is a few things to check. Collect open/closing operation should be checked with a Tool. Also, most likely...
  2. Replies
    1
    Views
    116

    Re: Fadal user near Coos Bay, Oregon

    ...try moving to and set Z Home (SETH) at Z+2.5 above normal machine zero..or possible (SETZ) command.....I think the machine should remember the TC position. See how the CS functions after you...
  3. Replies
    1
    Views
    100

    Re: Z height parameter

    ...might help if, knew what machine you have.
  4. Re: Arrow 750, error 39-97 Spindle not align.

    ...be very careful where and what you're unplugging before knowing. There are some bios battery things going on you don't want to lose. Good Idea to do a backup 1st to things.

    good luck,
    DJ
  5. Re: Help! Fanuc 18t RS 232 File Read & Write

    ...the Data Bit should be 7 and sounds like a Cable problem. There are few different ways to interface using RS232C. How do you have your cable wired or type Cable? Null Modem is what you need I...
  6. Re: HAAS TM1P air line inlet part — broken — need new one

    ...looks like its a water trap Part#58-2012 maybe.
    https://parts.haascnc.com/haasparts/en/USD/search/?q=air+filter&machineType=&model=&year=

    Enjoy,
    DJ
  7. Replies
    15
    Views
    1,442

    Re: New Milltronics owner MB-19D

    ...read Post #4 may help.
    https://www.cnczone.com/forums/milltronics/17762-software.html

    By the way do you have any Cad Cam in house system you use?
    here is a free one. It has Post Process for...
  8. Replies
    15
    Views
    1,442

    Re: New Milltronics owner MB-19D

    Good you have save Params...that looks like the Baud rate maybe set wrong between cnc to PC try 4800 or 9600........also there were alot of cheap USB to RS232 converters sold that had bad chipsets in...
  9. Re: KM3 with Ultimax II Memory Board failure

    ...I'm not a Hurco guy but......If, your machine will run with the borrowed board..there should be a way to get the files you need maybe.....I think you can Save the Parameters, Backup files to FDD...
  10. Re: KM3 with Ultimax II Memory Board failure

    ...sounds like the bios has reset ...do you have Keyboard to boot to BIOS? older DIN 5 pin plug somewhere 90's machines most of the time. Then, set the date/time then.... look for Auto detecting the...
  11. Re: CNC Converted Bridgeport, contantly shutting down at random times..

    ...Keyboard failing or sticky keys? Does your keyboard have a PC power button? Disable it ...if, possible.

    DJ
  12. Re: How download parameters FANUC-18T via RS232

    ...try changing "Bit Parada" to 1 or 0

    DJ
  13. Replies
    3
    Views
    196

    Re: Mill engraving

    ...It's a little tricky to do and it has been awhile sense I did this A axis Engraving on a Fadal 4020HT machine.....Cam Wrapping is one part of programming needed with a Fixed Subroutines L9201 for...
  14. Re: Send and Receive file with Fanuc Series 18i-MB

    ...I think the RealCom Mode is what you need to use. Then, each PC install a RealCom Port with NPort Admin program IF, I remember correctly....
  15. Re: G201X mosfets not making contact with backing plate

    ...Aluminum Can for shim stock. Remove the Ink and plastic coatings.:cheers:

    DJ
  16. Re: Hurco VMX50. Problem after disk repair

    ...If, the Time/Date is Jan 1st in bios then, all settings were lost so, you have to reset Time/Date and do a AutoDetect to find HDD to boot from in BIOS.

    DJ
  17. Re: Hurco VMX50. Problem after disk repair

    double post deleted
  18. Replies
    6
    Views
    1,717

    Re: 2006 Hurco VM1 Spindle Issues

    You said you never had this Spindle running so, possible that someone has a Parameter set wrong hopefully. Try...disconnecting the Encoder and see if, the Spindle errors out the same code. Check...
  19. Replies
    8
    Views
    3,536

    Re: Canned Cycle

    ...for anyone reading this thread without a manual..... here is list of G Codes for Okuma Lathe.

    https://www.helmancnc.com/okuma-lathe-g-and-m-codes/

    DJ
  20. Re: Slow toolpath down at end of straight line cut

    ...G05 or G07 may or may not change anything but, does effect the look ahead the control uses for accel/decel block to block.... try changing from what ever default is on your control. See what...
  21. Replies
    0
    Views
    457

    Re: Problems opening DWG files in V27

    ...try exporting with .IGS or IGES ext to Bob Cad.
  22. Re: Random E Stop on Bridgeport Interact 412 w Fanuc Controller

    ...Power Supply most likely. +5VDC Logic or 12v going to the Main CPU system. Could try using some Cooling Spray to find the problem Component....
  23. Re: Can I kindly ask for your help? EdingCNC 720

    ....welcome to the zone.

    After briefly reading thru your Eding Software manual...most of the Beginner questions are answered but, to someone new to CNC it's hard to know where to start process...
  24. Replies
    8
    Views
    421

    Re: Arrow 500 power cuts out

    ...inspect (if possible) or replace the main High Voltage relay/ contact's for Spindle Drive. Old age and mileage from Arcing they surprisingly do wear out

    good hunting,
    DJ
  25. Re: What is the minimum ceiling height needed for an 1100?

    ...if the travel of XY is only 18" x 11" just build a ceiling box where ever final location is going be. Also, I don't think telling Tomach you have changed something to something is not a good...
  26. Replies
    2
    Views
    419

    Re: Do I have a bad Amplifier

    ...here is a place to get Fadal Manuals
    https://flintmachine.com/fadal
    Good luck,
    DJ
  27. Replies
    5
    Views
    540

    Re: SRAM backup for mori seiki NV4000 DCG

    ...there might be a Backup file on the CF drive.

    DJ
  28. Re: What is the minimum ceiling height needed for an 1100?

    ...1st Project to design /machine Light Bar adapter to re-mount side ways.. :cool:
  29. Re: What is the minimum ceiling height needed for an 1100?

    ...there are machine Site and space requirement on page 34 of 293 in their Operator's Manual should help ya.
    https://tormach.com/support/mill/1100mx-installation

    DJ
  30. Replies
    4
    Views
    339

    Re: Fanuc 0MC doesnt run in MDI or AUTO

    ...there must be a way to Step the Tool Changer thru it's sequence of events, because it's out of position sounds like. It would be some type of Override Mode done with the CNC Control. Look in...
Results 1 to 30 of 499
Page 1 of 17 1 2 3 4