584,812 active members*
5,484 visitors online*
Register for free
Login

Search:

Type: Posts; User: GarageShop

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,288

    The voltage output with the TNC disconnected is...

    The voltage output with the TNC disconnected is 24v. Once the TNC is connected the voltage drops to 15.5v until it decides to power up at which point the voltage is 24v again. Same result with both...
  2. Replies
    9
    Views
    1,211

    Are you using a null modem adapter between the PC...

    Are you using a null modem adapter between the PC and the control?
  3. Replies
    4
    Views
    1,288

    Bridgeport Interact 308 w/TNC2500

    I have a Bridgeport Interact 308 w/TNC2500. I have a problem with the control powering up. It has always been a little slow but recently has got much worse. Once you power the machine the CRT and...
  4. They just completed the drive upgrade and almost...

    They just completed the drive upgrade and almost 5000.00 dollers later the machine is running again. I wish I knew abour EMI sooner. I did just speak with a guy from Bridgeport named Gary. He is in...
  5. Thread: KTK Drive

    by GarageShop
    Replies
    5
    Views
    1,056

    I have another question for you. I have call Bpt...

    I have another question for you. I have call Bpt but I cant seem to get any support from them at all.

    The tech working on the machine has installed a new CT drive. The spindle is rated at 6000...
  6. Thread: KTK Drive

    by GarageShop
    Replies
    5
    Views
    1,056

    Thanks George! You are a great help as always. ...

    Thanks George! You are a great help as always.

    [email protected]
  7. I am going thru a drive replacement now on an...

    I am going thru a drive replacement now on an interact 308. The orginal was a Control Techniques Vector v400. They are replaceing it with a New UniDrive SP from CT. Ill will post the results when the...
  8. Thread: KTK Drive

    by GarageShop
    Replies
    5
    Views
    1,056

    KTK Drive

    Does anyone have a manual for the KTK drives that came in the bridgeport machining centers. Mine came with a CT drive and I am having it replaced with a new drive. My prints show the wiring for the...
  9. Replies
    16
    Views
    2,739

    Anyone have a CT Vector or sutible replacement...

    Anyone have a CT Vector or sutible replacement spindle drive laying around for sale. Mine layed down today.
  10. Replies
    16
    Views
    2,739

    I believe the software is ver 12. As for the...

    I believe the software is ver 12. As for the prameter list, I would be happy to Fax you a copy if you need them for your archives.
  11. Replies
    16
    Views
    2,739

    The machine will lock up at higher RPMs. The 'F'...

    The machine will lock up at higher RPMs. The 'F' on the display will highlight itself and the machine will not feed. I assume this is what you mean by "sypder". If the Override is backed down a...
  12. Replies
    16
    Views
    2,739

    I also read in one of your other post (machintek)...

    I also read in one of your other post (machintek) that there was a prameter that could help with the look ahead hesitation between lines in the run mode. Would you mind sharing that trick?
  13. Replies
    16
    Views
    2,739

    It has the Control Techniques model v400 Vector...

    It has the Control Techniques model v400 Vector Drive.
  14. Replies
    16
    Views
    2,739

    I rarely use the M04 or tapping canned cycle so...

    I rarely use the M04 or tapping canned cycle so im not sure how long this problem has been around. I got an optical tach to check the actual spindle speed. In forward with a programed speed of 5500...
  15. Replies
    16
    Views
    2,739

    Heidenhain tnc 2500 on Interact 308

    I have a bridgeport interact 308 with a tnc 2500. The problem i am having is when the spindle is running backwards the actual RPM is half of the programed RPM. Doesnt matter if its in manual mode,...
  16. Replies
    17
    Views
    3,474

    Thanks Gus and Ray...The parameter 3410 was the...

    Thanks Gus and Ray...The parameter 3410 was the problem. Actually 3410.0 was set as in the parameter list provided in the machine but in the additional prameter 3410.1 you provided in the fax that...
  17. Replies
    17
    Views
    3,474

    yes, Just a dash.

    yes, Just a dash.
  18. Replies
    17
    Views
    3,474

    I have checked and rechecked the parameters. Here...

    I have checked and rechecked the parameters. Here are the parameters and values in my machine I can find for tapping.

    Minimum feed rate override (7110.0) - 100
    Maximun feed rate override (7110.1)...
  19. Replies
    17
    Views
    3,474

    Hey RMARCH, Thanks again for the prameter...

    Hey RMARCH,

    Thanks again for the prameter list!!!

    The programs that are erroring on the tapping cycle are proven programs that have made thousands of parts. I thought the same thing when my...
  20. Replies
    17
    Views
    3,474

    Heidenhain Help!

    I have a Bridgeport Interact 308 w/TNC 2500. I recently lost all the parameters and had to input all the values again. Everything is back up and going except I am having problems with the Tapping...
  21. Replies
    12
    Views
    3,485

    Thanks!!! I will go thru the list and see if I...

    Thanks!!! I will go thru the list and see if I find any differances.
  22. Replies
    12
    Views
    3,485

    That would be great! Thanks, Craig Fax:...

    That would be great!

    Thanks,
    Craig
    Fax: 940-566-5105
  23. Replies
    12
    Views
    3,485

    Heidenhain TNC 2500 in Interact 308

    I have a 1990 interact 308 with a TNC 2500. The machine lost the parameters and I am haveing some problems getting the machint act correctly. I do have a prameter list but not all the parameters are...
Results 1 to 23 of 23