Search:

hi which model of Heidenhain Control System ?...send me Picture of Control if you can
[email protected]

dear All
1- for seeing parameter on TNC 426 go to Edit mode ---select any program ---push MOD ---put 95148 then ENTER ---- for getting out just push END
2-for adjust Back Lash try to correct value...

is notimportant that you have proper voltage on the wire for the input ,..in fanuc system you need to have voltage for input that has been confirmed by means of diagnostig 0 or 1 ,..then if you need...

Dear Roberto
any things els can i do for you ? document that i send is useful ?
F.Sharifi

Dear All

if you need assistant on fidia control system assistant , please send me PM or leave messages on my profile , you can find all my connection detail on my profile .


F.Sharifi

hi
i send the file to your mail box check and informe ,..if you need assistant for an things on Simodrive just send me on [email protected]

regards
F.Sharifi

daer sir
i have seen many time this problem , this is just Spindle / feed stop signal missing ! it is not like Optional stop ,..all control system manufacturer uses this signal for safty module...

first things first ,..in all CNC control system ,..such as Siemens Heidenhain Fanuc ,..before all you must mention the axis is rotary or linear ,..then you must mention that linear axis measuring...

dear sir
1- check the machine uses the gear box or not
2- this matter of wrong gear change value , control always caculate the out pot to spindle dirve based on rpm that you choose , the send the...

dear sir
i thinks based on my experience you should check , the counting direction for A axis in NC machine parameter , in 840 D all axis mention by direction to use , you should check it before...

on 6RB system there is one board as power supply G0 - on this board there is Green LED , that means power ready but not enable , after enable happen ( 63-64) if every things ready no LED must be...

Dear Drew
Alarm 2 that means speed is deviated from command value !
please check following point
1- firstly be sure that you dont have any mechanical over load on spindle in any how from no...

Dear Sir
please check the attachment file for DNC setting on Fanuc OT
thanks
regards
F.Sharifi

Dear C-4
4n1 alaram means DRDY signal missing , it gonna happen during movment or stand still , if you sure about power input of machine ( fanuc needs 3 AC 200-220 Volt +/-10%) and because this is...

Dear All
hi , i have hitachi seiki with micon 16 and Fanuc 6MB , i can run M06 machine going to find tools and just wait , without any alarms . on micon 16 there isnt any red alarm . machine has...

dear all
with CIMCO edit software you can oden file then with NC Function and insert Block Nr. ( Ctrl +T) all file inserted with incrimental block nr.

check it out
F.Sharifi

Dear Sir
in the iTNC 530 the connection for RS232C and RG45 ( LAN ) is standard , with Cimmco Edit you can translate any Heidenhain to G code file ( go NC Function then find in this column the...

you need to have clockwise phase rotation for L1,L2,L3 Ac voltage supply for spindle it may be not important for axis ( depends on drive ) but if you can go ref , jog its ok , check the supply and...

this is always mechanical , in cnc lathe machine there is differnce ,... for position accurracy you need to adjusted axis with Min. back lash + turrect with min run out +and also good working of dog...

Hi ! thats not related to your first problem , 945 means that the hard configuration is incorrect for serial spindle , or a communication alarm , occurred , please check spinle all connection and...

Dear sir
generaly for Fanuc O series you need to have machine parameter list including 900 series ( machine configuration setting ) also diagnistig setting and keep relay setting ,..always you can...

hi !
i thinks i have it , but if you can wait for a week because iam in service trip , also its no needs to pay , i let you know if ihave and ask you for address .

f.sharifi

hi
401 is ready signal of servo drive is turned off ! DRDY if red light up consider on and let us know , if no light up there is always poor contact inside servo amplifire or there is problme on...

hi
900 series and diagnistig value included timer , counter and keep relay always described by machine manufacturer and deliver to customer by blue print or floppy diskett or punched or something...

Dear Sir
5 series alarm in Fanuc Oseries is related to kind of overtravel alarm . if you have maintenace book please clarify by alarm text .
if you dont have please check the machine axis for...

Dear Sir
in 5 axis machine situation , usualy ( just for rotary axis ) when machine is in enable such as manual mode or Auto mode all axis must be clamped . that means you can not move this axis...

Dear All
i need to find machine parameter for CINCOM e32 - Citizen cnc lathe machine that we had lost in cause of battry damage .including 9000 series parametre setting .

please help me if you...

Dear Sir
do you find somthing ? or not?
if you need machine parametere or some help to better setting machine just letme know
F.Sharifi

please check the Subroutine program for M06 is ok not ? you allways can fimd somethins like that in your Machine tool builder book

dear sir
please check the machine parameter 504to 507 for X to 4th axis in T series this is limit of Position deviation during any movment along each axis try to little bit extend that and try...