Search:

look in the section of your manual for Macro programming.
you should find a list of what you are looking for.

if you don't have a manual buy one

I used to fly cut aluminum plates with only double sided tape holding them down

could be a bad solder connection somewhere heating up and loosing contact. or maybe a fuse holder. do you have buss fuses ? if so take the fuses out and squeeze the clips together.

if you can afford a Fanuc robo-drill with 4th 5th option

try that #2202=[#2202+0001] line in MDI then Try #100 = 1234 and see if you have macro option on. (#100 should equal 1234)

if #100 = 1234 does not work you may need an option.

it will work. you answered your own question about the cables. you have one DB25 to DB9 going to your computer. new cables will be the same as this one.

on the DB9 DB25
...

you need to have the "helical interpolation" option to thread mill. for moving 3 axis in an arc.

sounds like you may be waiting for a M-Finish signal or spindle speed arival signal.

were you in a G96 mode during Rapid move?

if it stops and the cycle start green light is still lit leave it...

the Lambda should have a setting page to access all your send /recieve parameters.

I do not know your cable configuration. it could be a cts/rts or xon/xoff issue
does your cable work on any...

whats the file name on the flash card?

is it similare to the others you have unloaded from the machine onto the card?

Or Does it have a "name.ext"

Try renaming it to O3252

No extention.

i agree with superman. try looking for chips packd under the way covers. if it continues to change on powerups try moving the trip dog or switch a very little bit. .5mm

look for a setting in your transfer software for a delay between characters
set is to 20 -50 ms (milliseconds)
your flow control is Xon/Xoff thats good but it seems that hile your machine is...

i used to be

i ran them from 82 to 91 thats when i took a job with a machine tool dealer installing them and training customers on programming use and maintenance untill 2002.

whats your...

in edit mode type ODF push input

Operational
Disk
Format

i can not remember if you will loose your parameters or not. i do not think you will.

where are you located?

your not saying how your trying.

in edit mode
type O#### (<letter O and 4 digit program name)
push punch


if you want them all then as one long file type O-9999 then punch (yes you use the...

call 1-888-MMT-4CNC it is methods machine tools they will have what you need

Thank you all fopr help it turned out to be a bad MACRO MEMMORY CASSETT HR415 replaced it reinstalled Sram and everything has been good since.

Thanks again

RPM = 300
Servo motor & ball screw for collet open have been replaced.
voltages are 211v 24v 5v all good
Bar feed torque is set properly

it started happening once everyother day now every 20...

call Methods machine

not everytime but 3-4 times a day my machine freezes in the program on a "M7" command (open collet)

citizen M5 16 with a cav-is bar feeder.

G50 will set it

If you do a G28 H0 or a G91 G28 C0. follow it with a G50 C0

if it still unwinds its position all the way back to zero (or 2.9) there is a parameter that tells it to go to...

i have used Anilam several times to do what your thinking.

They sell a retro kit that includes a ballscrew for X and Y,
motors for X Y Z
mounting brackets for motors
a control with some very...

try this

Digi Connect SP - Compact Serial Server for Custom Applications - Digi International

we use them on 32 machines here with very good results.

it will let you use your network...

no way lube or bad bearings. take motor off and try moving ball screw by hand. you should feel smooth almost frictionles movement.

your G02 line is missing a decimal point .

Z-17 = Z-.0017

i think you want Z-17.

you can remove the G71 lines and run it, cutting air, to check contour is corect mathmatically.

You should be able to send multipl programs to the machine tool. as long as they are in the same file in your computer and have diferent O#### and no % sign until the very end.

Use O-9999 at the...

i am trying to remember EZ path but i think a thread is a surface finnish.
so if you do a tappered line can you then pick thread surface.?

that picture of dead servo is your turret drive. check voltage across U1 V1 W1 at the bottom og that board.

but a kit from. Anilam or some other company that has them for this machine. you can get servo motors instead of steppers and a control pendant with much nicer features.

any of the early Fanuc posts should work fine. But.

Do you use G50 or tool offsets?

That is what you will have to be aware of.

Most post will let you change output from G43 H# to a G50...