Search:

Hello
You get them where you buy your tools from.
These are tested cutting values, often already limit values.

Hello
A G0 should not be in a subprogram.
VARI11 is correct.
Write it like this:

HP
..
..
..
G0 X20 Z2

Hello
In the tool list under parameters:

Have a look at the work preparation:

http://support.automation.siemens.com/WW/l...300&caller=view

No you can’t. The license is only valid for the ordered packet.
Also it doesn’t make sense to have Sinutrain V7.5 on your computerand V6.03 on the machine.

You should find a sticker with the...

Hello as far as I know it should look like this:

N26 TRAORI
N27 G0 B0 C=DC(0)

In the second case I would say - G53 and SUPA are identical, that’s why the multiple programming occurred.

Hello

I wanted to do it once because my computer doesn’t have a COM interface anymore.
I did not have any success with it. But I used an adapter serial to USB.
I cannot say if it has anything to...

A contour with one technology is sufficient.
Set TRANS X, Y and repeat technology.
You don’t even have to be able to master the Siemens controller, that is everyday life.

Hello

That works under the process roughing- lengthwise- external under entering “DI

DI= distance feed interruption

I have tested several alternatives in Sinutrain. However without PROTON/PROTOFF.
However the error message unauthorized"Array-Index1" comes up continuously.
Either the software cannot cope with it...

Hello Firework

You had a lot of bad luck with our logistic system. I hope the packet was insured.
I don’t know if it works externally. But here are a few experts that can tell you if that works....

Do you go to simulation first?
Because only there you find the DETAILS
The standard value of the raw part with Shopmill is always set to 100*100
And you can only define them there.
If you can’t...

Hello

First of all you can also enter the Calculation parameter and jumps into the shopmill mask. That will simplify the raw part definition.
Under DIN it works like that:

*Simulation
...

With add- you add once your current contour: as its currently scaled,.
If you enter a new reflection, then all other factors such as scale, turn etc will cease to be in force.

Hello Cookie
You only have to scale it once.
Immediately after the program head “Scale” X0.7 Y0.7 Z1 and watch out it’s a new scale. So select it with alternative “NEW”
Then enter contour and...

If the multi-edge-profile is not too far away from the work piece zero point then you can also do it with abutting face cycle and T keyway cutter.

So axial in X10?
Where is the problem?
Are AGW(workplace limit values) available?
Ah- so radial offset in Y 10mm

Sparsely details!!!

How deep?
What Z-position?
With or without compensation chuck?

Hello
Do you want that the main spindle runs first of all.
The occupational exposure limit value has nothing to do with the referencing. I think more your programmed block.
Write T1 D1
G95 S1000...

Christiani offers machine key boards. But as said before it’s more for training purposes even though I sometimes used Sinutrain as an external programming station. However, to be one the save side...

Your traverse path when calibrating is limited and can be change. That saves you having to reset it all the time!

Hello
Sinutrain is a programming software and not a virtual machine.
So no collision, no end switch...
You should see any NC file errors yourself during the simulation.
Syntax error are displayed.

Of course we can help....
Click on the icon in the task bar, then onto settings.
There you have to select if you want to load the keyboard when starting the program or nor.. biggrin.gif

Hello
That works with G codes also over Shopturn.
With ShopTurn over contour and path milling.

On our machine it’s the tapping cycle.. I think a written one with g331 and g332.
That how it is called here....
But it’s also called like that with the machines from the manufacturer Grob.

Hello
How exactly can I understand the term "Enter"? Do you want to write a new program or edit an existing one ?
Do you get the message MDI program: L ????????!, right after you went to Open up?...

Hello
To stop the moaning biggrin.gif for a while I just say that Ultra Edit is a very good editor that can be extended dramatically with macros- but it is no CNC editor.

To fulfil all your...

Hello

Not in Dialog; only under EIA (ISO).
And only limited cause Fanuc has its differences...
I would say get ready for a new beginning. However it should not be a problem for an accomplished...

Hello

I spray them with Surface Shield. The spray is economical and puts a protective layer on the parts

Do your settings fit under file comparison?
It’s possible to switch from one window to another with the tabulator.
And it’s then possible to edit each block.
Also both windows stay open that way

To avoid colliding with the work piece, I set the cutter radius as my offset. In addition, possibly even a security clearance.
You can also set the offset to the value of the cutter radius to the...