512,717 active members
4,164 visitors online
Register for free
Login

Search:

Type: Posts; User: bloke

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    3,069

    Re: Error: Security Device is Invalid or has Failed

    Where are you located?
  2. Replies
    4
    Views
    56

    Re: need help bad! Hurco BMC 4020SSM, 1996

    Go into the control parameters and set N95:214 to 1
  3. Replies
    68
    Views
    942

    Re: Scary VM10U problems

    The 5 axis simultaneous option needs a written letter of assurance from the owner of the machine stating it won’t be used for certain types of manufacturing and that it won’t be exported to certain...
  4. Replies
    3
    Views
    51

    Re: VMX30U Door Interlock install

    Go to the Auxiliary page and select Utilities. Once there, go to Integrator Support and type the passcode 46268.
    Select Integrators and then N:95 parameters. Jump to parameter 230 and make sure it...
  5. Replies
    68
    Views
    942

    Re: Scary VM10U problems

    There should be a USB stick in the cabinet door pocket that can be booted to recover a saved image of the drive (if it was saved at the time of SSD replacement).
  6. Re: Help!! First machine!!! new to me 2002 VM1 wont boot controller!!

    They seem ok. You may need to reload the software. Do you know which version you were running?
    Are there any disks in a folder in the back cabinet?
  7. Re: Help!! First machine!!! new to me 2002 VM1 wont boot controller!!

    Enter the BIOS pages and find the hard disk settings and post them here.
    You should have cylinders, heads, sectors, wpcom, lzone and the access type (lba, chs or similar).
  8. Replies
    3
    Views
    110

    Re: Hurco 2416 Freezes

    Check the CPU for burst capacitors.
    Remove all but 8MB of RAM. Swap around to see if the fault clears.
    Remove all I/O cards and the Canbus Controller (the keys won’t function with this removed).
  9. Replies
    3
    Views
    178

    Re: HURCO KM3 HELP!! Servo Fault

    SC is short circuit. Check the brushes on the motors and blow out the carbon dust to begin with.
  10. Replies
    3
    Views
    178

    Re: HURCO KM3 HELP!! Servo Fault

    What servo amps do you have?
    Any lights on them when it faults?
  11. Replies
    68
    Views
    942

    Re: Scary VM10U problems

    I had to sort out a coolant through spindle leak on a machine in Frankfurt that had the same model of Fagor encoder inside the head assembly. The encoder was half submerged in coolant that had been...
  12. Replies
    68
    Views
    942

    Re: Scary VM10U problems

    The clamping is performed by the air pushing a tapered cylinder into a similarly shaped recess in a split brake ring. This ring opens out very slightly to grip inside the housing. It is returned to...
  13. Replies
    68
    Views
    942

    Re: Scary VM10U problems

    I don’t know of any brass rings that seal the air accessory tube. There is normally a cap sealed over the threaded part down in the table.
  14. Replies
    68
    Views
    942

    Re: Scary VM10U problems

    The brakes on the rotary axes are actuated with air and released with a spring called an ‘anti-rotation ring’. Strip-down is simple and reasonably easy. Seal kits are available.
  15. Replies
    5
    Views
    226

    Re: VMX Tool Changer Leak and Lube Levels

    The oil you need is 120 to 150 ISO grade gear oil if you have the electric toolchanger. If you have the little perspex cover with the proximity switches then it's electric.
    to re-align the arm, put...
  16. Replies
    20
    Views
    494

    Re: Hurco Computer identification

    I’ve just rebuilt a rack with almost exactly the same setup as you have. I’ll snag a picture of the finished unit on Tuesday. All you’ll need is the BIOS settings and a couple of other minor things.
  17. Replies
    20
    Views
    494

    Re: Hurco Computer identification

    That Peak715 looks ideal.
  18. Replies
    20
    Views
    494

    Re: Hurco Computer identification

    Do a search for Nexcom P777 or P715 CPU. You’ll find a processor that will fly. The 715 will be easiest to get started.
  19. Replies
    20
    Views
    494

    Re: Hurco Computer identification

    Looking again at your pics, you have most of what you’ll need to get one going. One has the passive backplane but nothing else, the other has a DSP, Canbus Controller and a hard drive. Snag a CPU and...
  20. Replies
    20
    Views
    494

    Re: Hurco Computer identification

    The older versions of software needed a dongle to run that matched the version of software running with it. Do you have anything connected to the parallel port (25 way D socket)?
    When you get up to...
  21. Replies
    20
    Views
    494

    Re: Hurco Computer identification

    It’s a little tricky if you are trying to run the software after V2.15
    It may get sluggish as you get nearer to V2.30 upwards.
    You will need a few software tools to make it run and you’ll need to...
  22. Replies
    20
    Views
    494

    Re: Hurco Computer identification

    It shouldn’t matter. Everything depends on what you load on the hard drive. The second pic has an early Pentium motherboard instead of the passive backplane seen in the first pic.
  23. Replies
    4
    Views
    217

    Re: Need to buy encoder for Hurco BMC 4020

    Search for a ROD320.020-1250 or ROD320.020-2000 and see about changing the resolution in the CNC config parameters.
  24. Replies
    24
    Views
    787

    Re: VMX30 and BMC3017 question

    I don’t know yet. We still have Jatons at the minute...
  25. Replies
    2
    Views
    236

    Re: Hurco VMX 40 axis problem

    Have a look at the Y axis Servopack to see if the display is jumping around.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4