Search:

Sounds like since there is no alarm it is looking for the matching wait gode in $2 toolpath. I would check over there.

If you have WIN CNC you can check the Queing commands. not sure but...

Yes, with the 3 flutes you get more cut because the helix allows more broad and deep removal. each flute gets a worload that in a sense simulates greater feed or allows for more area of chip to fill....

one thing I see may be that you are already calling the cutter to .912" in the program. If you have too much height set in preperation it may be X axis stroke that is causing the alarm. Do you see...

+1

My boss gave me drawings and said. " Hey, We needs these parts yesterday... Thanks I really appreciate it."

THen with no more technology than some paper, pen, scale and calculator I would...

many times I have problems like that I go with a 3 flute mill. vs. 4 flute. Then decrease the rpm and increase the feed. But one question. Are you facemilling or cross live tools? When hard milling I...

Typically there is a standard machined in "interference amount when the BF collets are manufactured.

But many times you can find loose screws at the headstock sync device when this is happening....

You should be able to turn then sync the subspindle. I promise G650 sync turn is the best way to remain true lengths.

your parts .312 long... Are you running a L. Hand cutoff? If not then set your machining data super tight. Like: Part length .500" as tight as possible. If not successful try the opposite and set it...

your parts .312 long... Are you running a L. Hand cutoff? If not then set your machining data super tight. Like: Part length .500" as tight as possible. If not successful try the opposite and set it...

Chuck the hell out of the delrin. THen run the GB snug as comfortably possible. I ran tons of delrin before on swiss. I had an L-20 dedicated to Delrin production. All the doors and gaurds removed...

sounds like a torque setting is too high. On plastics I take the standard calculation (for every 1mm stock diameter = 1% torque E.G. 20mm = 20% torque) then cut it by half. The integrity of the...

G650 support with sub spindle collet.

I run a job that is very long. Gun drill almost 5" deep and cross drilled etc. Even though I turn the large end out where the ID work is at, and have all...

You should be able to set defaults to post it as a .txt file, if not then generate the code with the post processor. SAve it in Notepad as a .TXT in both the file name and the file type. Save it on...

Post the code or send it to me in txt format and I will load it to see if I get the same errors. Then, correct if so, save, and send it back to you.

[email protected]

or...

I commonly make a boatload of different knockouts for the parts and the collet size. Sometimes I have even made "get r done" versions with a drill press, bench grinder, and a hand tap. From brass.
...

WHAT ALARM ARE YOU GETTING?

Working on an L3 16/20 with meldas 320 controller it was one of the fans to the drives having a ton of dirt and grime. You should open up the rear cab and clean with a shop vac. Do not use compressed...

If so then these guys are getting old. So are te encoders. TRy swapping an encoder from the Z2 axis and check out if it works. Then swap the switches over and see if it works. THis was the process of...

No, G600 will just cancel and run independently. You are going to use a catcher of some sort? Like an A-16 or B-12 machine has?

I can help you program it but there will need to be commands in $2...

I ran this sample code in My A32 machine which is M70 Mits controller like the L20 VII. It hangs up after the variable call. Still trying to read where it could be faulting. It hangs up like a...

Those encoders can be qualified and then deemed repairable or not. I think we paid about 1/2 what a new encoder costs.

[QUOTE=carmstrongls1;1226119]If the cycel time is not a huge concern then use G650 commands to support the thread with the sub spindle. If you do this it doesn't matter how long the thread is as long...

If the cycel time is not a huge concern then use G650 commands to support the thread with the sub spindle. If you do this it doesn't matter how long the thread is as long as it can be grabbed in one...

Mathematically the machine took the code just fine. I am trying to figure out if I am unwrapping the C2 axis and pulling back the Z2 axis at the correct feed and speed. Any tips on calculating this?...

Im about to do my first threadmilling on a swiss. 7/8"-20 UN thread on sub spindle live face attachment. Any tips for entry of the thread. Mine is a through hole.