Ding Ding Ding ... we have a weiner !!!
Switched the jumpers over to US Mode - nothing wired to Relay 2 so ... I guess my slow process of deduction and your ace knowledge of a smoke free...
Type: Posts; User: MiniSoCalCNC
Ding Ding Ding ... we have a weiner !!!
Switched the jumpers over to US Mode - nothing wired to Relay 2 so ... I guess my slow process of deduction and your ace knowledge of a smoke free...
SCHP disabled .. yields same results buzzing and red light on relay 2...
Currently set INT'L mode ... gunna try US and see if that shuts one of these relays up :-)
Thanks John ...
Just tried that ... still buzzin. Jumper selector for Relay 3 - is bare - no jumper on it at all ... still buzzin.
Red Light behind Relay #2 is lit RED.
I have SCHP enabled...
http://www.cnczone.com/forums/attachment.php?attachmentid=382950&stc=1
Update 12/30/2017 : Big Boy Pantalone's ON - Controller Box Power ON - "It's Aliiiiive!"
NO/None/Nada... wicked, not so magic smoke either !!!
Hats off to all the kind gents who gave...
I have a C10 in my box o' goodies - I had no plans to use - LOL guess that could work eh ? Happy day!
Ive got this one - it says C10 R 11.1
...
Put my new handy dandy Klein multimeter [ cuz I broke my el cheapo Harbor Freight unit lol ] to the test, put one end on the 5v DIN rail power supply V- / GND and one the GND closest to PIN 1 -...
This same issue came up in another thread ... His g0704 build thread ... He responded .. That he is well, and he is centralizing all his sites content [ or something to that effect ] to a single...
Well another day another Plot Twist !!! Arrrgghhh ...
Im going thru the manual again today after landing some more wires as per some prior posts and reading up for clarification of jumper...
I stand corrected - it was the Gecko 320x - not a C6 board - u r absolutely correct and the limitation was the 80V max output ....
Interesting thing - hes rigged up a switch between the KBMM-125...
Ok ... see now youve gone and got me all intrigued and wanting to fritter away hrs researching a way to do this LOL dahhg Nahhhbit !
Did you perchance watch the video I linked in here of Hoss...
John,
I cannot even begin to tell you how grateful I am to see this drawing and getting some confirmation on how this could/should be done !!! Thank you man ... times eleventy billion ...
...
Thanks John ...
So i can run my 4th axis stepper driver "and" the COM/5+v via another wire off the same connector on the c11GR out to the ssr ? No conflicts or concerns? Very interesting ...
...
Progress Update 12/28/2017 : Part Deux Deux....
So my current status is ... Ive taken the power leads from my contactor in the box - off the KBMM-125 - and hooked up a spare power cord to wall...
Progress Update 12/28/2017 : Part Deux - C11GR Coolant Power Relay / KBMM-125 Spindle Control Wiring
Ok well - Where to begin to describe 7+ days if hair pulling and screaming at your computers...
Progress Update: 12/28/2017 - Wiring... more and more Wiring of this blasted control box !!!
I felt a pretty solid sense of accomplishment right around 12/22/17 as I had wrapped up what in my...
OK - so the utilization of forward and reverse of a DC motor thru my KBMM-125 / C11GR appears to be above my current components and ... especially MY capabilities. Im going to take a step back for...
Ok - many thanks - that clears that up nicely. I suspected as much but - guessing with electricity is never a good thing.
Yes ... as you describe here in quotes is how Im currently set:
Good Morning John, [ its still morning here ]
Thank you again for your excellent reply. Apologies for being so dense in this area .
So a couple more points of clarification for me if you will...
Reading your post most literally - in the P.S. - Would I need to run the card in the Int'l Mode [ Im in USA for clarification ] in order to get Spindle to reverse with Mach ?
I was making the...
John,
Awesome post - reply - MANY thanks sir.
Just when I thought I was about to get away with this solution - simple and easy ... now theres a whole nother wrinkle - LOL.
OK so more...
Mike,
Epic reply brother - thank you ... just the type of thoughtful detail a newb like me needs. Pretty much nailed what Im after and where Im stuck. I have elected for the Solid State Relay...
and ... yet another thread that veers off into another direction where the title is left unresolved ... arrrgghhhh !!!
Was there ever a resolution to wiring the C11G BoB for a SSR ---> 110v outlet...
Kudos gents ... great build - shes a beaut! Christmas Chips - what a great present ..... Inspirational. Thanks for all the updates and posts - and sharing the good bad and ugly.
Maybe Santa...
Excellent news ... gave a brother a bit of a fright :-) Glad all is well - Merry Christmas / Happy Holidays my good man.
Thanks for the update ...
while we're here :-) got any links on...
Concerned ... somethings up - His domain expired 12/6/17 ...
Anyone heard from Hoss ?
old thread bump ....
resolution? dont leave me hangin bro
Apologies to sound so / be so newbish here ... but I cannot picture a "crimped" connection here for these connections. Do you perhaps have a picture of such a crimped connection you are referring...
OK - so I landed a bunch more wires for the power and common / grounds for the sepper drivers off the 48v / 12.5 A Keling supplied Power Supply from my 3 axis "kit" ... and I'm kinda trippin ...
...
Yeah .. basically I did give that [ or an iteration of that ] a good solid think .. almost went that way with the KBMM-125 - outside the main enclosure in its own 3D printed box ... but then thought...