thanks for your answer.
try to communicate the driver with the PC. Install sigmawin + 5.7.5, the driver for spindle sd drives.
but when I try to connect I get a compatibility error message or...
Type: Posts; User: jlviloria
thanks for your answer.
try to communicate the driver with the PC. Install sigmawin + 5.7.5, the driver for spindle sd drives.
but when I try to connect I get a compatibility error message or...
regards,
I have lathe ML26. centurion 6, when I execute a command s500 m3, for example. the control displays an S560 CW speed. I try to move the potentiometer to zero%, but the spindle does not...
cordial greeting.
We have a machining center with mazatrol M32. The lubrication pump stopped working, our technician removed the pump. but I leave a 24VDC cable sticking in the machine housing....
regards,
I have a horizontal machining center, FH50, fanuc control 15M.
Who can sell me PMC parameters and macros (9000 programs) please.
Jorge
regards,
I have two lathes with control centurion 7, one of them presented problems when starting, by mistake the technician deleted all the information of the compact flash.
we can format,...
Hello, I want to do what you did, but I'm not clear when you say that the A: drive (floppy disk must have the command "sys".).
Where do I get the commando "sys" or where do I download it, or where...
We have a lathe hardinge model CS-51 conquest snake T51, Control fanuc 18T.
The problem is the following.
When we run some cycle. (G71, G72, etc.) the machine works perfectly.
But when...
hello,
no hablo ingles espero me puedas entender
te vas a parameter
3 2 1
solo debes de presionar el...
buenos dias amigo,
tengo los dos programas de cambio de herramienta encantado te los paso dime como hacertelos llegar
por otro lado
no he podido hacer DNC en mi maquina sabes como se hace...
thanks friend
verificare what you say
jorge viloria
hello friends,
I tried to run a program by DNC without success I get the alarm:
001 TH PARITY ERROR
the machine manages to read something from the program
thanks advance
friends,
I have the same machine, I have parameters in inches but in print.
I can scan and send by mail
sight that I have another problem
alarm: 235 missing cycle start condition
when attempt to do what you say, and passage to the position page clears the FF to him
I have the following problem:
alarm: 235 missing cycle star condition
whenever I run a program, check the tail stock on spindle and are in good condition.
what else can it be?
in TEST I...
Good evening,
friends I have the following problem when I move my vertical axis horizontal machining center, makes a noise as if hitting metal to metal, it is strange that sometimes leaves is not...
I found this following the path you told me.
X0006 5
exdexl
0
ME THAT INDICATES THAT?
Good morning,
Friend apology but the truth do not know if I understood.
is that I am Colombian and I do not speak or write English, but the problem is that the X-axis moves slowly in a...
friend thank you for your response,
BUT THE TRUTH not know WHERE CAN I SEE THE SIGNAL x6.5
Thank you in advance
JORGE
FANUC 18MC
CENTER MACHINING HORIZONTAL
KIA H50
MODELO 2000
4 EJES
2 PALLETS
PARAMETERS WILL BE OR ELECTRONIC
good evening,
I have a problem with the x-axis when you move in fast moving x only moves with a preview of 495mm/min that only happens in a positive sense
in advance thank you very much
...
good evening,
I have a problem with the x-axis when you move in fast moving x only moves with a preview of 495mm/min that only happens in a positive sense
in advance thank you very much
...
good evening,
I have a problem with the x-axis when you move in fast moving x only moves with a preview of 495mm/min that only happens in a positive sense
in advance thank you very much
...