Search:

Thanks for that info.
I have a PMDX 126 bob.
There was a problem last year where a mouse got into the cabinet, and urinated on some of the electronics.
I used an electronics cleaner and some...

It won't let me edit the post. But, I tried to start it up, and the Estop won't reset. Both buttons are cleared, too.

Thanks

I have a Hurco mill that has been running from Mach3 for about 12 years.
It has set for a few months. The trend to start it up and it won't reset from the eatop buttons?
Also, the charge pump ...

Can you message me your email address?

I have the original manuals for a Hurco KM3P.
I would sell them, if interested.
My machine had the BX control.
It went to.0001 accuracy.
Also, other leftovers from my retrofit.
Drives,...

I have a lot of replacement buttons, new bulbs, switches, pin connectors, vari- drive spindle speed changer, etc.
Would make a great deal for all.
I have it stored in a metal cabinet, to keep...

I still have all my stuff from my retrofit.
I went with a mach3 conversion back around 2010-2011.
Buddy Maughn in Florida checked all my boards and sent them back.
It turned out that my wiring...

Thanks for the info.
The way it is wired, would it be possible for him to clean it without removing the boards?
They way they are wired, it would be a big ordeal.

Opened up my buddys mill the other day.
It was running good, but stunk real bad.
There was a wad of papers built into a mouse nest.
Also, there is a sticky looking film on everything.
He is...

I used a Rosewill brand from tiger direct. I believe it was less than $10. It was highly recommended, and it worked.

Sent from my SAMSUNG-SGH-I547 using Tapatalk

Steve,
I haven't been on here in a while.
I did a retrofit and have some spare drives and boards, etc. That came out of my machine.
Would you be interested in these for spares?
Let me know....

[/QUOTE]


I have the master tapes. If you have a way to load them.

Does your machine have the tape drive still in it??

Mine is like that. The timer is actually a mechanical clock movement, and works just like bloke said. It has rotating cams that operate the lube switch at timed intervals. Mine is set up so that the...

Guys,

Mariss at Gecko told me that the 320x's were checked above 90volts. It seems he may have said they are tested at 100+volts before they leave the factory. ( safety measure only. DO not...

Here's 2 more pics.

Looks pretty good.

159507

159508

JAckal

Here are some more pics that I got from Dave Rothermel the other day.

This machine belongs to one of Dave's friends . They call it the "Kokomo Hurco mill".:)

159502

159503

159504

Hello Brian,

I have a similar retrofit. You would do better to keep all servos ( I think from past discussions, servos & steppers won't play together ;) ).

There are some Hurco servos listed...

rbalister,

This is just something to check.

On my Hurco I had drive problems and other stuff, too.

Sort of a "ghost in the machine"

While doing the retrofit, I pulled the servos to change...

Fasto,

Thanks for posting.

That will be very handy for someone. The pics really help, too.

JAckal :cheers:

Bob,

It looks like you have it going on!


Once you start you can't stop.

It was hard for me to stop working on the retrofit to do my paying jobs.(chair);)

rbalister is correct.

I tried and some of my round connector wire had been disconnected previously.

I ended up using the comm port on an MPU board bought from AMTS.

The MPU board has the DB9...

Gordon,

You have a PM with my email address in it.

Jack

Dave,

What Rick says sounds right. I'll look at mine to make sure, but Rick has it correct.

Jack

bpe,

I have an emulator and MPU board that came from AMTS. It was in my Hurco that I retrofitted last year.

It works great, there were other problems with my machine.

If interested I can...

My original encoders were 1000 PPR ( pulses per revolution).

Here is a link about them:

http://www.cnczone.com/forums/servo_motors_drives/126798-these_litton_encoders_worth_re-using.html
...

Bob,

I'm thinking the shaft on mine is 1/4"?????? I'll look and see.

It is turned down small on the end ( factory done) for the encoder.

Here is a pic of the encoder installed;

Click for...

Hello Bob,

That is looking real good. On the arm that holds the console, I made a new one for mine.

I'll get a pic tomorrow. It mounts in the lifting eye hole on top of the ram.

I kept...

Dave,

Here are some pics of my control panel.

It is kinda dusty from use in the shop.

So far it has ran about 7 paying jobs.:banana:

The first pic shows my large cable ( Umbilical cord)....

Dave,

On mine, I am using the air brake solenoid.

It is 110 volt powered.

It has a 24 volt operated relay that is connected to a toggle switch on my main control panel ( monitor area).
...