Hi Okuma guys,
I need your advise about OSP-5000M DNC-B technical book to solve W30 communication error.
If an one have MCV-A electrical wiring diagram, I need to use it too.
Send me at...
Type: Posts; User: iNUC
Hi Okuma guys,
I need your advise about OSP-5000M DNC-B technical book to solve W30 communication error.
If an one have MCV-A electrical wiring diagram, I need to use it too.
Send me at...
I'm not sure it is right whether or not . I asked DMGMORI, they told me that this controller is not Heidenhain (But Heidenhain had took over them). It is Philips or Grundig / Model : PG1220 Series,...
Hello Guys,
I'm just bought DMU 50V 5 axis MillPlus V310. Unfortunately, IDE HDD is faulty and the machine can not boot up the system.
I'm looking any one can help for HDD Ghost for this...
Hi,
I'm maintenance engineer and I have OKUMA LC-50 with OSP-5000L-G Controller.
Pls advise how to change Language from Japanes to English.I found that this machine no have backup diskett...
Hello,
I also having DMU50V 5 axis no manual book. I have no experience about this. Could you please send me some document as PDF that you have. Pls send to [email protected]
Best Regards,
Dew
Hi,
I want to use serial link (RS-232C) between Charmille Roboform 20 and PC Computer. But I don't know the procedure how to operaate the Roboform 20. Any one here know how to do it, kindly give me...
It seems that you losed all parameter. Need to input them back.
Good luck.
Hi,
912 Share Ram Parity Error
Replace the axis control card that plugged-in main PCB.
No need to clear the parameter.
Good luck.
Hi,
Check MRDY LED on the operation panel, if no lit I think PMC Parameter is not input yet.
Hi,
I have Mori MV-65 with MORIC-3Y ( Yasnac-MX3 + 14"CRT) controller, I want to change NC Language from Japanes to English,
Any one here how to do the procedure? I heard that it needs to replace...
Hi,
I have old Mori SL-5 with Fanuc-6TB but no any manual books. I'm looking for Parameter Sheet, Electrical & Ladder Diagram, Operation & Maintenance manual and part list. If you have the list...
Hello,
I bought 2 units of Nakamura Tome / Model: TW10 / Controller: Fanuc-0TTC / Twin Turret & Spindle Turning Center. Unfortunately, there is no any manual book with these machine.
The book that...
Hi All,
I'm lookingfor Fanuc Connecting Manual as the below,
B-62753EN FS-16/18MC Connecting Manual ( Hardware)
B-62753EN-1 FS-16/18MC Connecting Manual ( Software)
I have this control with...
Hi there,
I'm looking for FAPT LADDER as below part number;
1. A08B-9201-J500 #EN With B-55193E Programming Manual
2. A08B-9201-J501 #EN With B-61013E Programming Manual
3. A08B-9201-J502 #EN
...
I have another machine , Mazatech Ultra550, Mazatrol M Plus, Year 1997-3. Also long time stopped got alarm no. 2 Emergency Stop when power up. Any one here know how to solve, kindly advice.
I have Mazak Slant turn 40N with Mazatrol-T Plus, Year 98-01 long time stopped. When I power up the alarm 33 Emergency Stop always showing on CRT I can not clear this alarm. Due to I have no any book...
This machine ( Turning machine)is parameter gone and already re-input back parameter, the problem is turret head can done T1,T3,T4,T6,T7 but T2,T5 and T8 can not finish, it moved forward and reverse...
How do I know MTC8A or B? We have no parameter for MNAP L III and ATOM paramerter.
Any method for checking?
When I power up and press MNAP screen, there is only FLD LOADING, after 30 second MNAP L III is show on CRT.
The problem is I can not access in MNAP ( Showing Mnap L III but can not go inside ), no red led on PCB.
Any one here know how to make initialize MNAP-L III for Meldas-300 series ( Lathe)?
Before make ram clear, i need to write down old data first, but I don't know how can I access.
Please advise,
Hi All,
The machine issued an alarm PARITY ERROR becasue of poor Battery. I would like to know how to make RAM CLEAR for Meldas-335LG. Any one know kindly tell me or send me an email at...
926 FSSB ALARM : Replace the axis control card.
Al-24 shown on SPM is EMG state. when machine ready this alarm is gone.
DEW
[email protected]
I have 3 units of Mori Seiki / SV-50B / Fanuc-18MC (A02B-0228-B502). I would like to put Fanuc High speed function. As far as I known, it need to put RISK 64 and ATA Dataserver card. Any one here...
Any one here having operation manual GFZ-66234EN/05?
I already got the software from our good Vietnames friend, Any one here know some MTB having password to see or correct the ladder on Fanuc ladder III? Some MTB are opened, but most are closed when...
Fanuc here quite terrible service, they don't want to reply us. Any one here having?
Where can I find a Fanuc Ladder III Software? I need very urgent.
Hi Jung,
Thank you for your reply. Could you contact me at [email protected], I will send you the data and some photo.
Thanks
Any one here having ROM Writing machine (OE1 and OE2) for Fanuc-OMC. I would like to correct or make a new PLC data.
Thank you.