584,830 active members*
5,782 visitors online*
Register for free
Login

Search:

Type: Posts; User: rwskinner

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: HAAS ST 20 Y Lathe Coolant Spraying Out Where The Coolant Line Meets The Turret

    Is there an easier way to check it other than removing the top cover?
  2. Replies
    1
    Views
    443

    Re: Dc Power supply AC ripple

    Typical for most industrial electronics is less than 2 volts ac peak to peak and while I personally think that's high, that's what I have in my control documents.
    Something more fitting is that most...
  3. Re: HAAS ST 20 Y Lathe Coolant Spraying Out Where The Coolant Line Meets The Turret

    I'm curious, was yours a standard O-Ring, or one of the pre-formed rubber rings from Haas? I've seen both.
  4. Re: HAAS ST 20 Y Lathe Coolant Spraying Out Where The Coolant Line Meets The Turret

    Take a small putty knife or thin screwdriver and pry the nozzle back and blow it out with air. The nozzle is spring loaded and chips will get in there.
  5. Replies
    13
    Views
    3,652

    Re: Haas standard coolant filter

    A few years later, and no filter at all provided!!!
  6. Replies
    2
    Views
    721

    Re: Calmotion Lancnc

    I was sure you could map a drive in Windows to the IP address of the Calmotion then just drag files over or post directly to that shared folder. I could be mistaken but I think you can. Have you...
  7. Replies
    4
    Views
    1,066

    Re: Fadal monitor colors

    Good idea, but then I think you would have to add a BNC to VGA adapter, then put this inline with that. Remember Fadal is using the BNC output.
  8. Replies
    4
    Views
    1,066

    Re: Fadal monitor colors

    They had a couple different display cards. If you had just the old monochrome CRT with black background and green letters, then you're stuck with black background and white letters. I believe the...
  9. Replies
    5
    Views
    1,073

    Re: Tool Number with decimal

    Thanks for the feedback.
  10. Replies
    3
    Views
    892

    Re: Threading on Haas TL1

    Do you have a picture of the IPS screen and settings and the code it produced?
  11. Replies
    16
    Views
    1,837

    Re: Another spindle orientation problem

    That would definitely do it!
  12. Replies
    5
    Views
    1,073

    Re: Tool Number with decimal

    If this isn't fixed yet try the Zero Memory command I believe. You have corrupt memory due to low voltage. It's in the DIAG section of the maintenance manual.

    Function 5 = ZERO MEMORY
    On the...
  13. Replies
    16
    Views
    1,837

    Re: Another spindle orientation problem

    Then there is a problem. If I type DI then DS, if I rotate the spindle it will change the Spindle Orientation to 01 and stay there unless I move the spindle past the sensor, then it goes back to 00....
  14. Replies
    16
    Views
    1,837

    Re: Another spindle orientation problem

    Try it without the M19 and see if the input is read. That way it won't fire the solenoid.
  15. Replies
    16
    Views
    1,837

    Re: Another spindle orientation problem

    I know you said you checked but you have to separate the issue to find out if it's mechanical or electrical.
    Using DS - Display switches will tell you if the CPU even see's the input from...
  16. Replies
    2
    Views
    1,376

    Re: TL Lathe Tailstock Rigidity

    Did you come up with anything on your tailstock?

    I have a 2005 and turn lots of 15-18" SS shafting and setting the tail stock sucks. Once I get it set, I leave the power on during the entire time...
  17. Replies
    3
    Views
    1,214

    Re: ST10 with manual chuck

    Old thread but just in case this ever comes up again, Yes.

    You can remove your hyd. chuck, unscrew the drawtube if it doesn't clear. I prefer unscrewing it so I don't damage it or get coolant...
  18. Replies
    5
    Views
    1,081

    Re: SETP wrong turret, Froze loading screen

    What ended up working?
  19. Replies
    5
    Views
    1,081

    Re: SETP wrong turret, Froze loading screen

    Did you get it cleared?
  20. Replies
    5
    Views
    1,081

    Re: SETP wrong turret, Froze loading screen

    You most likely short the battery out for a few seconds like a cmos battery it will wipe all the memory and settings. I believe removing the cpu card then removing the RAM card from the cpu board...
  21. Replies
    16
    Views
    1,837

    Re: Another spindle orientation problem

    Be sure to let the forum know what you found so it can help others down the road.
  22. Replies
    16
    Views
    1,837

    Re: Another spindle orientation problem

    From the video, It looks like your spindle plunger pops in place and the VFD quits turning, but it looks like the timing is slightly off. I can hear the solenoid release like it passed the sensor.
    ...
  23. Replies
    16
    Views
    1,837

    Re: Another spindle orientation problem

    There is an pneumatic plunger that locks into the divot on the spindle. You should have 80-90 psi air pressure for it to work. When it aligns with the notch in the spindle, the hall effect sensor...
  24. Replies
    16
    Views
    1,837

    Re: Another spindle orientation problem

    go into diags and see if the orientation sensor is working. Do this by entering command DS for Display Switches. There you can see if the orientation sensor changes states. ORIENSP Switch closes...
  25. Replies
    16
    Views
    1,837

    Re: Another spindle orientation problem

    We need to know where to start troubleshooting so did it just start doing this, or is it a new to you machine? Have you lost any settings lately?
    Usually, if the spindle is turning too fast to...
  26. Replies
    2
    Views
    709

    Re: Lathe Wear Offsets

    Since nobody seems to know or take the time to answer, I would guess the only time tool offset are read and applied is when you tell it to with the T0101 or whatever tool is called. The reason the...
  27. Replies
    2
    Views
    709

    Lathe Wear Offsets

    Are the wear offsets immediate, or only used by the controller on the tool change, or rest?

    In other words, say you have to fine tune an insert while boring a hole before the finish pass.
    Can you...
  28. Replies
    4
    Views
    1,143

    Re: Fadal spindle speed issue

    I don't know anything about a VMC15 but most of the Fadals have a High Low idler system. Do you know if it's working?
    S750.1 M3 will command 750 RPM in low gear. S750.2 M3 will be 750 in high...
  29. Replies
    4
    Views
    753

    Re: Fadal 4020 Carousel Drum # Wrong

    Sorry, I didn't see the Fanuc when I read it. Who Knows? hopefully someone with more experience chimes in.
  30. Replies
    4
    Views
    753

    Re: Fadal 4020 Carousel Drum # Wrong

    Have you tried using the command SETTO ? This will establish this location astool number one. From there the count should be correct.

    Richard
Results 1 to 30 of 500
Page 1 of 17 1 2 3 4