Search:

i have a Fanuc 10m system here with this "a20b-0008-0280-04b" board and a dangling db25 serial cable. the motherboard has the"a16b-1210-0350" option board that i believe the dangling serial leads...

we have an okuma 3va that may have the bearings going out. did you find an answer to your question and would you share info?

i have a nomura bn110sr with a fanuc 11m control.
the tool changer seems to be wanting to work, but will not. the tool readout on the pendant shows T00 in spindle and T00 in pot. the machine does...

I am not in front of my machine atm, but, will this macro work for 16M or does there need to be edits made?

thank you,
carter

thank you, sir.
the problem was 2 gummed up limit switches that confirmed the proper gear was selected. they were both stuck. got it going and am now calling it good... for now.

M40 low
M41...

My company has salvaged a BEAST of a lathe and we have it running, but, no manuals. For the most part, everything seems to work, BUT, we do not know the proper procedure for initiating the correct...

Anthony never responded to my question...

we have an fh45 with an 11m control, but, i will not be near that machine until monday. remind me (this thing emails me) and i will see if i have an mcode...

does anyone have any experience with these machines? we have one with an 11m control and an indexing table (90 deg)

we do not have a manual detailing the procedure for turning the table and we are...

Anyone out there have the parameters for this machine? The control is a Fanuc 6T.

nevermind.. float switch in the coolant tank... derp

we have a toyoda fh45 that was bought for parts, but, this machine may run.
when the machine is started, the alarm light comes on, but, there is no alarm/operator message.
we can home out the...

email sent. Thank you, Sir!

no, the only thing in there was the binder with operator manual, parts list, ladder and electrical books inside.

we have a LARGE binder, from Daewoo with several books in it. The blue one is titled Parts List

Ahhh Doosan... i called the Houston office yesterday around 3:30cst

ACE V85
AV850021
Fanuc 16M

i have lost the PMC Data TBL Control and the PMC PRM Data

Could anyone please help me restore the parameters for the toolchanger on an ACE-V85 Fanuc 16-M? The operator was trying to recover from a magazine error and initialized the eprom.

I have a FH45 4 axis with an added axis (5th) that i need to remove. the control is an 11MA and i am not seeing what i need to in the manuals (if i even have a complete set). any help would be...

does anyone have manuals?
need to know how to operate tailstock (shot pin).
if you have any info, please let me know

10-2012
If anyone ever has this exact problem, our machine is an M4 Lathe with T1 control.

The resolver/Pick up unit went out and the numbers on the old part (listed in my previous post) are...

can anyone lead me in the right direction for getting a resolver/pick up unit/encoder (or whatever mazak calls them) for an M4 lathe?

the ink on the tag is faded, but, it looks like a
RT-6XB-11...

... i can dream, cant i?

thank you very much for your help.

While im thinking about it, do you know of a functioning Mastercam X post that can be used on the T1? i have heard that this is akin to searching for Bigfoot or Nessie...

Right.
What i am needing to know is can a separate "post processor" be made for the oddball machine? for all intents and purposes, the programs can be used on either machine, BUT, one must pay close...

dang... somehow i knew that was going to be the answer...

ok, why does one like mazacam and the other is cranky with it? any special changes i need to make?

We have two Mazak M4 lathes, both built within 6 months of each other. One has different software loaded and the grooving cycles are different. one works fine with MazaCAM, the other has "trash" in...

off topic, i know, but where can i get "nc fadal"?