Search:

Hey John. I got it figured out last night. I kinda like how it does a helix.
Do you know how in/tan and out/tan work.

John, Well thanks to you I blew up my transformer!!!!
just kidding YOU were right I wired thru the transformer and it worked. It also made it run alot quiter and spindle runs alot smother!!!!!!! If...

Hey John any luck on drawings. Also tried something today , when I turn spindle on and try to move axis I still get the same alarm. After I clear that alarm and just try and move an axis, withe...

ok that might be where my problem is the main trasformer I dont think I am right in that area, where is t1 t2 t3 are those at the transformer.

do I just hook 230 single phase to that or do I need to still go thru the main switch.

The input power thats the one marked 230 output next to 230 3 phase out put,the lugs are they on the parajust or am I out to lunch.

John Let me know how I can rewire for single phase if you can. Thanks You do know I owe you about 4 cases of beer!

Emergency stop motion error, thats the alarm. Here is what's going on--
have a hurco kmb1 w/bx controller, with the parajust, 5hp spindle motor, and 5hp rotary converter. 230 volts is from wire to...

How easy is it to do that? I just got off the phone with a guy from cmc and He said that I need to also check my step down transformer, like you said I do not need 230v at contactor. I also am...

well interesting I did check the volts to the acc contactor and it was 230+
also I tried to see what axis was giving me the problems and the x and y are good they moved smooth and together so I...

That voltage was from ground.

John, I got 230+ on leg to leg.

John where is the acc contactor, is it the one to the right of servoes
also where is my logic board and not sure if I have a flood pump but the switch in the back is on mist should I disconnect pump...

Sorry The three wires coming out of my converter to the main switch with the big fuses does it matter which wire goes where.

Which one is the third leg? also does it mater which wire goes to the main power switch. Because I have the 2 with the most volts on the outside and the other in the middle.

Power problem I hooked voltmeter to the 3 legs and on two of them I had 230 and one was at 48v. got the samething on the acc contactor in right cabinet. now I checked the three legs to ground I think...

so you think I should tune the servos. and not bother with the transformer

I ended up calling a guy and he said I should hook up the transformer that could solve the problem if that did not work I need to tune my servos.

yes everything runs fine till I try and move with the spindle on, the transformer is the on on the machine on the back. what kind of voltage should I have coming out of my converter on each wire. how...

One thing when I wired it I did not go thru the transformer was that wrong should I re wire it so that it does.

Hurco FET Servo Amplifier I think thats what I have. If voltage is dropping how Do I fix
it.

Well how do I run in single, where is the spindle drive, servo drives, Are they in the right side cabinet, also if you go to cmcsystem.com click on tech tips and page down 4 times that is the alarm I...

yes I have one, I am no pro but I now the basics pretty good. and yes I went the phase converer route an Anderson 5hp they said I would not need anything bigger
because it was not a hard start...

yes the clogging goes away as it speeds up. got any clues as to my motion error. when spindle is not on I can move all axis but as soon as I turn spindle on and try to move a axiz I get that alarm...

Yes it does, also On the cmc web site they have some tech tips and one is what Im going through I think. It says to adjust my servo amplifier is that a good Idea. or is it the clogging noise?

Well, have a problem, I wrote a small program from the book and It seems that when spindle on and I am jogging one of the axis I get a motion error. Now I can jog all axis just fine, but when I go to...

yep and tonight I plan on playing around on it to learn as much as I can. Again THANKS
ALOT.

Well I ended up removing the encoder and manually moved table and that worked. THANKS.

Well John, It ended up being the air switch stuck or just plain dirty. I took it apart and cleaned up a bit and got it. So I went to zero table and as you stand in front of machine it went in x to...

Thanks John I will give it a try tonight. When you say the "the brake will not come on without the COR being energized\latched, the click you hear is the brake relay trying to work, but without COR...