Thanks for the help Greg
I will try a few more things. At a point now were i been trying to get this machine to run
and running into opsticels
I just may scrap it
Type: Posts; User: Sebalj
Thanks for the help Greg
I will try a few more things. At a point now were i been trying to get this machine to run
and running into opsticels
I just may scrap it
Tried to check the batteries on the BIOS but its almost impossible with out removing it
thanks had the workstation a fives come back still no monitor
no mine is bigger and more square its sayas OSA metal probably 25 pin
the workstation board # is 3-424-2290 A02
how did you load the picture
Hi Greg
Im not sure how to upload pictures on here
From what I was told the video card is part of the workstation board
The plug in the back of the monitor says OSA VIDEO
the monitor was...
I have a 2000 Arrow 2 A2100
Need help
I had the monitor on the mill replaced back in April All worked great until end of July. Then the monitor went out Sent the workstation to Fives came...
I do some work at a company in Ontario Canada
Running a 1996 Arrow 500. The X servo motor started making noise while moving.
Several years ago (before my time) I found out they I assume had same...
Hi All
Just got a used Arrow 2 up and running. Ran a trail program all went well
In order to start the program again a message came up to open and close the door
Were can I turn that off.
So...
I have a arrow 2 with simodrive 611.
Can anyone tell me what the dip switches on to of the power module should be set at there is 6 of them
Machine is power with 400 V
Thanks
Thanks Greg
Hi All
I been getting a Arrow 2 (500) Simodrive 611 up and running
Had few issues. Got help from a few people on here.
Had to send board to Micacron for new battery and re flash.
Had a local...
Hi All
I am located just outside Toronto Ontario Canada
If anyone on here is in Ontario
Besides Circo Machine does anyone else service and repair drives on Haas machines
Thanks
Hi
Cincinnati Arrow 2 Ekk year 2000
Can anyone help with this
On to of the diskette drive on the Simmo Drive 611
I noticed there is a Ethernet connection
Can this be used to connect and load...
Hi All
I have Arrow2 500 year 2000 Acramatic 2100
Would like to upgrade the hard drive and upgrade the connection to USB or Ethernet
Is this something I could do myself and has anyone done it...
Thanks maver1ck
You are very helpful. It is much appreciated. I have the machine running spindle correct orientation, air is blowing out on top of spindle motor, tool changer is working. As to the...
Yes I will see if I can remove it. Thans
Did you ever have these come up during start up
Thanks for the info It was the wires Once I swapped them went to spindle
Hey Mike
Went in this morning took the cover of the tool changer were the power is saw the cam roller going backwards
Spoke to my electrocution swapped wires and all good now
Thanks for your...
Yes Took the cover of the tool changer were the power is saw that the cam was going the wrong way
Switched wires all good now. Just got a couple of things that pop up on start up looking for...
Hey maver1ck
Phasing is okay spindle is running the correct way.
It moves forward about an inch it seems like its hitting a hard stop when I tell it to do a tool change
I had all the covers off...
Hi all
Slowly but sourly getting my arrow 2 simodrive 611 up and running
Had a few glitches but do to helpful people on here got them sorted
Machine is running axis aligned spindle runs
issue I...
Thanks coop31 I was able to confirm with Greg Woods that it is 400 V
Hey Coop31
Thanks I sent you a message would you mined calling me
Thank for getting back to me. Spoke to the sales guy. Did not get much out of him. The machine came out of MADARA pharmaceutical R&D in Pittsburgh. First response was they had a step-up...
I just purchased a used Arrow 2 (SIMODRIVE 611) YEAR 2000 from a facility in Pittsburgh. Had it moved to Canada
There is a sticker on the back that says 230 VOLTS
Got it powered up and control...
Hi
I run a arrow 500 Acramatic 2100 control. Mainly produce mold parts
Recently I did a job were a block was ground square I picked it up in center. Did some milling found out I was of center
Did...