Is this LB10 or 10M? Sometimes on M machines toolholder drive doesn’t retract fully causing Jam. Also standard turret can get chips inside if o-ring fails…may also cause Jam. Have you removed the...
Type: Posts; User: OkumaWiz
Is this LB10 or 10M? Sometimes on M machines toolholder drive doesn’t retract fully causing Jam. Also standard turret can get chips inside if o-ring fails…may also cause Jam. Have you removed the...
Sync wait command. Stops processing with no read ahead until both M100s are completed.
The green screens were not L-G controls but were L controls typically. Is yours for sure an L-G ? Ie does it have animated graphics and not just the Trace? Communication protocol is different on the...
The low pressure brake comes on during contouring. The high pressure brake is used when clamping. What typically happens is that the film of grease that is on your brake eventually wears off during...
Turn the key that locks out the edit and parameters. Problem fixed.
A quick tip: Your X Zero Set is recorded on the Management Data Card in the electrical cabinet of the machine. If it is there,(a lot of people think they are helping when the remove it for safe...
First...are the cables and jumpers the same on both machines? If not, match them. Next check your parameters on the LB 15 to make sure they match the LB-10. If you are not even getting garbage,...
You've got a timing issue of when the W move is occurring. Depending on parameter settings, your G140 and M01's can work like P-codes, so with the M01 it may not be reading ahead as much as with it...
Kurmay is spot on...
G144 W-axis control OFF command
G145 W-axis control ON command
The lathe also needs to send the Barfeeder an “ok” signal. It is usually labeled “Auto from lathe” or similar. The lathe must be in auto or MDI with link ON and have no alarm in order to generate the...
Yes it is most likely caused by the lathe and it is missing a normally closed contact in the E-stop circuit that opens when the lathe goes into the e-stop or non ready condition. This is sometimes...
The variables work on your machine. Look carefully at the code and remove the code for axes that you do not need. (Like is shown for the Y axis) Now I’m assuming that you have added the needed code...
The U100 control only had geometry offsets and wear offsets were a very rare option. Most likely not on your control.
There should be a Management Data card in your electrical cabinet with Stroke end limits and X zero sets recorded. Enter those numbers in the appropriate registers.
Variable limits are...
I’ve seen that alarm when the encoder is going bad. Sometimes you can adjust the gap to cure it, but usually it needs replacement. Superman is right when he says the motor and encoder are reading...
You are correct that moving the taps to the required voltage indicated will work.
Phase can be confirmed by checking for hydraulic pressure. If that builds then phases are correct.
I believe...
It requires a software reload on that machine. Kurmay may be able to help you out. It is not a parameter setting until you get to the P100 and later controls.
What you are looking is for is VZOFZ[1]=123.456 or VZOFY[1]=123.456...
They can be put into a program to set the work offsets if you like.
You can find a lot more if you look in your manuals for...
EC overload alarm is caused by the relay tripping. Which relay is usually an indicator of what device has the problem. Plugging a vacuum cleaner into the 120v 2a outlet on the machine can cause this...
Try to open it with different word processors. Sometimes notepad will open it without the extra lines when wordpad or word will add them in.
In your System Parameters, you need to go to the PR Zero Offset and shift the encoder position by the amount that you are off. It will give you a "Power on effective parameter set" alarm which...
I think the only way is to turn on the spindle orientation function and use the M19. It is software only and requires no hardware.
Maybe Kurmay can grant your wish?
Best regards,
You must PATCH the spec code file.
You may need to unprotect the file to accomplish this.
On non windows machines:
Boot with SW switch ON
DIR MD0:,PN:;P
PROT FILENAME.CNC;U
PATCH...
KMWPAT,
What you seek to do is possible. Use software handshaking and it will work fine.
Cable is critical to success. Both machines need 4-5 and 6-8-20 jumpered but once that is done, 2-3 and...
There is normally a proximity switch that detects when the arm is fully up. It may may require a little adjustment. There should be an indicator light on the prox showing when it is retracted.
You need to locate the button for moving the w axis with the pulse handle. It will allow you to move the axis off of the Stroke end limit. (manually move it, reset stroke cancel switch, reset on...
It appears that you may be able to "shut it off" by changing the spec code in a few places:
EC spec code:
With ATC =0
With TS axis =0
Without TS-axis drive motor =1
They should be in the spec...
That motor I believe is used for both driving the tool change arm and the magazine rotation and switches by mechanisms between devices. It is not uncommon to have the switching position get out of...
Well, release the e-stop button and press reset of course!
I’m guessing you probably have a piece of external equipment removed such as a Barfeeder and the Estop for that device has not been...
Typically it is used for a boring operation so that you can retract without dragging your boring bar. Orient, shift away from orientation, retract.