Search:

504008

Hey

I have to mill it on both main and sub spindles. I have Y axis on the upper turret but not the lower. I have attached a little sketch. Bar dia is 46.5mm and across the flats is...

Hey

We currently have a job in our shop that is high volume and requires us to mill flats using a Nakamura Tome WT150. We are trying to find the best radial live tooling heads for the job. We have...

Thanks for the response. Ill give it a try but the part is a steady runner with very high volume. Adding passes and slowing down the SFM to much may kill the cycle time to much.

Hey

Im using a 2 line G76 to make a thread. The thread does not end in a undercut so I am wondering if not having a lead out will affect the tool life at all?

Thread is M34 x 1.5 in 1215...

Hey

During a change over in my shop a lot of time is spent removing and replacing tool block on the turrets of CNC lathes. At the moment we just use hex keys, pipes, and the occasional wack with a...

Really no1?

try 3500rpm and a .005"/rev feed

Hey

Like the title says.. I am wondering what could be the reason for a diameter to be on size but if the machine goes down for 10mins and no changes are made... why would the diameter of the part...

I have thought about this (#3000) but if the alarm is cleared with the reset it will just come backup again when the machine is restarted.

Controller is Fanuc 18i

I do seem to have 1 machine...

Hey

I have programmed in a few custom messages in our programs. The issue is that when the message comes up to give the operator information the indicator light stays green. I would like the...

The 29 value helped a lot. Eliminated a burr on the break through edge. Had previously tried 60 30 and 00 but 29 seems to be exactly what i needed. THX!!!

Thanks for the reply!!!

Hey would just like an opinion on our G76 code we are currently running I did not program it just setting it up... Not ashamed to admit we rarely single point thread so it is not something I am to...

I will have to shut a machine down and try some stuff. If the Toggle switch makes it read the M30 as M99 maybe i can enter in a M30 with the M99 P values to restart it where i want.

When in the memory restart position it reads M30 and restarts from the top line of the program. If the switch is off then it reads M30 as the end of the program and stops.

We use bar feeders that are activated by the block skip function automatically. Machine automatically skips the block skip lines and when it goes to load a new bar it activated the machine to read...

I would like to use

Main prog ---------------------------------------Sub prog

N10 TOP CUT ----------------------------- O1234

N20 (PROGRAM) ---------------------------N40 (SUB...

I cant use that because it is never known how many parts it will run until it is shut down. We are a high production shop and run the same parts all year long with one operator running many machines....

Hello

We have nakamura tomb wt150s with Fanuc 18i controllers. I would like to have a main program that does a top cut then switch to the sub program and continuously run the sub program untill...

I work in a CNC shop with high production numbers. We do have runs of parts that require a 33tooth spline to be broached 5.5mm deep. The spline constantly servo torque alarms the machines. We have to...

Thanks for the reply mcode and thanks for the ideas!! seems like now the job is put off for another week but I am definitely excited to try it out.

Anyone?

Hey

I am new to using G112 and would like a second opinion on some code. Just a little reassurance or opinions to build my confidence and understanding on how it works. I have to mill a round hub...

Hey

I am new to using G112. Before crashing a machine..... I was hoping I could get some feedback on some code so maybe I can have a little confidence when running it. I need to make a round hub...

At 4000rpm can your servo motor keep up? Is the thread pitch a mess or is the thread just heavily burred? Im with Tom and slow down the RPM

That would be it. The .42 is a .8max dimension but I am guessing you already figured it out and .42 is the length that makes it blend?

248254

Quick sketch from paint since thats about all i have on this computer to use. The .6 rad blends the angle back to the straight.

Hey

I have a print deviation that has come in from a customer. We do not do a lot of rads that are partially formed at the end of an angle and if we do we usually have length specs for the angle...

We have Many WT-150s in our shop hooked up to an automated line. Issue is that we are starting to have an issue where if you are cutting on both spindles you make waves on the cuts. I am now having...

Going back to waylube. The lubrication pumps started pumping ALOT and some not at all. Some machines having to fill up the tank 3 times in a 12 hour shift. Now the pumps are needing worked on and...