Hi Anybody have a link to the schematics for haas vector drive original link is down
please i really need them
Type: Posts; User: jannie@eelectro
Hi Anybody have a link to the schematics for haas vector drive original link is down
please i really need them
Hi Keanan where in SA are you based i can maybe help my cell 0769792833
The spindle drive is working if i manuall set to run its not a fanuc drive its mitsubishi
some how i thing the controller think the spindle is running that is why the alarm the alarm then switch...
Hi anyone know how to switch to diagnostics on Harrison alpha 550s plus
Please help i need to get up and running again
I know Mbservice have the procedure how can i get hold of him
my email...
Hello everyone i need some help with my Harrison alpha 550s
when i start it up it gives me spindle speed monitor alarm 15 manual says encoder or encoder cable ive tested encoder it is fine tested...
Hello everyone i need some help with my Harrison alpha 550s
when i start it up it gives me spindle speed monitor alarm 15 manual says encoder or encoder cable ive tested encoder it is fine tested...
Hello everyone i need some help with my Harrison alpha 550s
when i start it up it gives me spindle speed monitor alarm 15 manual says encoder or encoder cable ive tested encoder it is fine tested...
OK Machine Is running
Thank for all the help
jannie
hi alexfanuc
OK got the parameters loaded to head 2 two switches was swoped dont know why but fixed it
now machine gives me waiting for reset esp,rrw off :1 not sure what is holding the reset...
hi AlexFanuc
there is a button to switch between heads 1 and 2 but nothing happens when i push it
only alarms is axis digital parameter 417 on head 2 but that is because of parameters not loaded...
Hi
can stuff like doorlock or hydraulics cause the problem of stuck in MDI mode
thanks for the reply Guys appreciate it very much
Ok i did load the parameters for path 1 and PMC parameters but cant change the path and conttrol stuck in mdi mode
first time i loaded the pmc...
loaded NC parameters then load pmc Parameters with rs232
went trough the pmc file and the last few parameters was wrong on machine input that with the hand
error is gone now
but i noticed my...
Hi
want to know procedure to load parameters for fanuc 16-ta with sub cpu on option2 board
i have 2 parameter sets one for maincpu and one for option2 board
i can load maincpu parameters and...
Any body that can help me
im looking for pmc Data Table for a Mori seiki zl25b/500 with
MF-6D CONTROL PANEL
cpu a16b-2200-0900
opt2 a16-b2200-0930
io...
Any body that can help me
im looking for pmc Data Table for a Mori seiki zl25b/500 with
MF-6D CONTROL PANEL
cpu a16b-2200-0900
opt2 a16-b2200-0930
io a16b-220-0955
i have parameter file and...
Max-Mod
thanks for all the help it was the heap setting ive changed it to 100 and it works
will look out for the new version
just another thing is there somewhere a instruction manual or...
Max-Mod
when i start up the bord error led is off as soon as i do any of the commands like L or p 0.010 the error led get a 65hz signal
and the communication stop
looks like as soon as it tries...
yes it stops at the = sighn with l command
and when i enable the drive it stops at servo enabled =
the error led is not blinking
hi Max-Mod
ive compiled the unified source for use with h bridge but
when i program my board
an try to set the pid parameters it seems that the program cant read the data from eeprom if i put p...
Thanks Max-Mod
that was the problem my compiler was v3 upgraded to v3.21 beta and it compile without errors
hi Max-Mod im truing to compile your unified source code and get following errors please help
Clean: Deleting intermediary and output files.
Clean: Done.
Executing: "C:\Program...