Search:

I have a Mac Turn 30 whit the Hi-G control Low Acceleration / Deceleration option according to the mdc. The problem is that no one seems to know how to enable the funktion and how to set the...

Got the settings from the lokal dealer,

OSP-side
Optional parameter “RS232C(CH1)”
? No.1 : stop bit “1”
? No.2 : Ready signal “1”
? No.3 :...

Ok, that sounds interesting! How can this be done? I have the floppies and a device for floppy to usb. Can I view the settings in my pc?
Thanks.
/Samuel

Hello.
Today I messed up. I was connecting the machine to a computer and changed RS232-parameters. Now the communication between the magazine panel and the controller is not working. Alarm-D 4738...

Thank you for the response. I have purchased a used scale on Ebay and will try that one first. If that turns out not to work I will check whit JoeAmada. At the moment the machine works so I will wait...

Hello.
I have a Promecam STP-C pressbrake with a DBM-A control from 1984. One scale is bad and propably need to be replaced. The original is a Heidenhain LS513-scale. I have been in contact with...

Hello.

The machine does not respond to M334 (work load finished). It does not work in either MDI or auto. I want to use it for not have to press the work load finished button manually when only...

Ok, then I know.
Thanks

Thanks for the reply.
Normaly I dont want it to auto power off, just some times when leaving workshop whit machine running. I have seen that some models have a button somewhere to easy turn this on...

I have now looked into the parameters and found where I can enable the power shut off. I can also chose whether an alarm should trip the power off. And then a time parameter, that delays the shut...

Hello all.
Okuma MA40HA year 2000 whit OSP U100M.
I have a question regarding the automatic power shut off option. Seems my machine has got it but I can´t figure out how to enable it.
I cant find...

Thank´s for responding.
What choices is then left for running large programs?

/Samuel

Hi.

I have searched on the forum and seen a couple of threads regaring this subject, but I still don´t quite get it.

I recently purchased a Okuma MA40HA year 2000 whit OSP U100m controller. So...

Thanks for the replies. I will try this out.
It is mostly for situations with deflection this will be needed in my case.
Is there maybe a way to add finish passes inside the G71? So that the...

Hello.

This is propably very basic but I have not yet found a way.

I want to cut at thread in only one cut, for example to remove burrs after a finish cut or add some extra threading passes...

I have searched but did not find were I set that. But there is a parameter somewhere. Sorry.

Hello.

I set the part catcher by a parameter. Is there one for the door too? In that case, which is it?

Thanks.

Hello everyone.

A simple question, is it possible to get the IGF to output M90/M91 (door close/open)?
I managed to get the code for the parts catcher (M76/M77) to be output and I hope it is...

I am a little embarrased to say that the problem is solved. I called a tech who almost immidietly discovered the issue. I did not know that the spindle speed for m-tool shuold be set whit SB=xxx ....

Thank you for answer Pro.

What sensors are you referring to and how do I do that?

Now I have tried some more and figured out that if I run another program using the m-tool it works.

This is...

Hello everyone.

Problems whit Okuma LB300-MW year 2001 OSP U100L whit disk VDI40 turret.

The M-tool suddently stopped working. When the M13 command is given it just spinns for a second or so....

I changed the value from 0.007 to 0,02 and the problem did not occur anymore. But what I dont know is why the IGF outputs M147 in the milling operation. It clamps and unclamps before the tool is...

It seems you found the problem Wiz!

Now the fault happened again and I can see that M147 is flashing in the block data. The Rdiff is 0,015 in the C-axis. Is it possible to change the in position...

Thanks for your answers!

In this case the c-axis does not clamp at all. I can hear a sound when it does and also see the lights on the valve shift. Or can the c-axis float off before clamping?...

This problem is solved, turned out to be a broken fan in the electric cabinet. Replaced the fan and the problem has not happened since.

Hello everyone.

I recently purchased a used Okuma LB300-MW whit a OSP-U100L controller. Today i tried some milling including the c-axis. I do the programming in the IGF.

A few parts did work...

The PC is a desktop.

I will check this out.

Thanks.

Hello everyone.

I need help whit my PC to CNC connection. The machine is a Chen-Ho with a Mitsubishi Meldas 520 controller.

Everything has worked fine with sending programs to the machine for a...

Thank you all for quick replies.

First to answer Deadlykitten, I have a few jobs where this kind of optimation is worth it. But the main reason is that I want to learn more about the machine and...

Hello everyone.

I would like to alter some of my programs to be more efficient. What im after is a way for the machine not to wait for the spindle to reach the right RPM, this is when in G96 mode....