Looks like Maverick is helping you out! He is the best! If there is any info you stil may need, I can try to figure out how to copy ot!
Type: Posts; User: Arrow eeyore
Looks like Maverick is helping you out! He is the best! If there is any info you stil may need, I can try to figure out how to copy ot!
Thank you for your response and help, I have truly appreciated all the help you have given me over the years I found a blown fuse in my switch panel for my phase converters. After replacing the...
Thank you for your response. There maybe a lot of truth in your responce! I found a blown fuse in my switch panel for my phase converters. After replacing the fuse I retested the coolant pump (in a...
thank you for the response, I am considering just swapping wires...but I am reluctant because something must have failed, My spindle and table directions operate in their normal directions, so I am...
Scratching my head! today I lost coolant, after blowing out lines, checking the key way on the impeller etc, I think my pump is spinning backwards! I am not a electrician and have little...
Thank you for the responce!
Actually have a older computer sitting there with a serial port and was ready to cable them together to try it! My current computer only has vga and usb ports.
I did...
Thanks for looking! The Adventure continues, After replacing the Power supply, having my communications board repaired and replacing the CRT with a LCD screen, I was excited when it all booted back...
Thank you for the info!!! pretty sure it acted as the fuse for one phase of the supply to the power supply in the CPU. I was able to have my board repaired by a lady locally! "SAVED"!!!!
I just recently had a problem with my communications board, it was in the circuit for the 220 volt supply to the CPU power supply, blown fuse on one leg with the communications board becoming the...
Thank you for the response, I looked at the boards
Listed on ebay, several with simular part #
But mine ends in a A, the current batch ends in B & C, do you by chance know the significance of the...
My Mill stopped booting up, had a blown fuse, but also looks like it damaged a embedded conductor in my Communication Board!
Any body repair these? maybe have a used one sitting around?
1996...
GREAT!!! Thank you for sharing your results, I have yet to spend the money, but will feel much better about it now!
just found this....assuming its the CRT and not a board...transformer...etc?
New Universal retrofit LCD Monitor for Milacron Acramatic 2100 and Tree TPC-2100
Thank you for the responce! any experance/info you can offer on what it takes to upgrade to a LED Screen in one of these controllers?...but if I can just get it back to normal...and feel assoured its...
Hello and thank you in advance for any help offered! Was setting up my mill today, looked over and my controller display was blank with a blue/black squiggly line running through it. I quickly...
I did go ahead a swap out the capacitor, after doing a bunch of goggle searches, trying to educate myself on capacitors, guessing the different numbers between the two might be batch/manufacturing...
if you have the transformer...just need to wire up to the AB BB and CB input terminals in the transformer!...before powering up the machine..test your transformer out put for the 230!
Again, not a walking talking encyclopedia on how to power up machinery, but...I believe the one drawing you posted shows the required transformer, to bring in 480 volts, you will need to connect your...
not sure if your Arrow is the same vintage as mine, but the pic you posted looks like the main off/on. on mine, I have a stand alone transformer that was supplied with my mill when purchased new....
I went ahead and pulled the replacement PSR unit, removed the cover and one of the screws on the negative side of one of the capacitors was hanging loose. After attempting to screw the screw back in,...
I could be wrong, but if I remember correctly, there should be input locations on the transformer for diffrent supply voltages
Assuming your thinking I switched polarity on the Bus? I am positive to positive, negative to negative on the bus connections between the PSR and S/D unit, and then across all of the BDS-4's . I took...
Thank you for interrupting your TV Viewing!
Machine does not have glass scales
Have Manuals, but unfortunately, always a little out of my element tiring to figure out failures on my machine...
Hi And thank you for taking the time! 1996 Vintage Arrow 1000, about a month ago while starting up the mill, while powering up, things went bang, With help from Maver1ck and Chris & Mike Kilroy...and...
I have done thread milling on my Arrow 1000. Never programed it in Rap, did it using Gibbs
Thank you for the info, the testing info was spot on, my PSR unit does have continuity between the La and Bus + terminals, weighing my options between purchasing a used unit or having mine repaired,...
there is a gentleman that post here that goes by maver1ck, he has helped me with boards and hard drive issues, and other issues. great service!
this is not mine, just a picture I borrowed. I do believe it is the main power supply that provides power to the other servo drives...any way, I do think mine is dead! ...
Hello, It looks like I am in need of a working PSR4 5 250 7500 for a Arrow 1000. Things went pop on Monday, and judging from the smell...not in a good way!
If you have one, scrapping a machine...