Search:

if that doesnt work, swap drive cards from Y axis to X axis. see if the problem follows the drive card. If it does its a bad drive card.

There are yellow and black wires going to the drive cards. There is also a power supply that the yellow and black wires go to. Unplug the big connector on the power supply and plug it back in. Unplug...

I don't know, I cant tell on this machine. See attached picture.

When I look from the top down I can see the TSC and the drawbar actuator, this stuff is sitting on top of the motor. I either have...

Seems like most spindles drop out the bottom. I need to change the draw bar springs. Does anyone know how to remove the spindle to get to the draw bar springs? I called my local service department...

Sorry, not sure what this is all about. I was just trying to figure out how to use the comp tables for my Haas 310 Trunnion. It repeats very good by the way, better than the specs, always has, but...

Hi, I notice you commented on using the comp table for a trunnion. I have a trunnion 310 and am trying to dial it in as well. How do you use the comp table?

Thanks.

Does anyone know how to use the axis compensation tables? Talked to the Haas factory and they said "they don't know". I find this to be insane.....I have a 310 Trunnion that needs a tiny bit of...

Not shouting at you, hoping the guy reads this because you were probably unaware of the second way to home a Haas machine. "Power up restart" is the easy way. "zero return" takes a few seconds longer...

>>>>Starting up the machine with "zero single axis" button bypasses the need to have the spindle shift any gears and will home normally. :stickpoke

His machine obviously need maintenance but this...

This is it. zero out all axis one at a time using the "zero return" single axis button. then you will have a zeroed out machine. Then, run the spindle for a while. this will warm up the moving parts...

Somehow, it just feels better when everything is clean and matches. :cheers:

The white parts are original and did not need re-coating. I think because all the white is up higher and does not get hit by shop carts, hoses and other shop hazards. Typically the front of the...

Got this machine 9 months ago, used it for a while but it didn't match my Integrex so I had to fix it up. Black sheet metal parts are powder coated. White parts are original. Total refurb cost...

We have Haas and Mazak. Mazak is built like a tank and yes more rigid! but for the price of one Mazak, you can buy two Haas almost. Haas is way way way way way easier to use!;) Get a Mazak if you...

Haas all the way, made here in USA, parts are cheap and machine is easy to fix. Plus, most schools have Haas machines and chances are you will find employees that already know The Haas control. And...

So what it was is, during shipping or who knows, the pallet shift lug/hook thing (the thing that pushes the pallet in and out of the machine) was mid stroke so therefor not on the limit switch!

I just got this machine and am trying to set it up.This is an AJV 25-404 2 pallet machine.

I get a "128 outside interlock axis" ALARM.Cannot home x axis. :confused:

I have no alarms. Y and Z...

I will swap encoders, I have an extra one. I posted this in case there was something I missed. Thank you for your help.

Machine is old (1988) but clean and has no coat hanger duct tape chicken wire repairs. All components work and machine holds dimensions well. Lately, the Z axis shifts .030 up after a while of...

I have an ajv25 and an Ajv32. The ajv32 was born 8/88. I just bought the ajv25, it was born 12/88. I set up the F92~F94 perameters to make the ajv32 and ajv25 work with eia tool offsets. They both...

You are correct, it is only my opinion based on wanting to be able to program anything and everthing. Conversational programming will make you money but has limitations. It is good for the beginner...

Somo, do yourself a favor and forget about learning mazatrol or any other included with the machine garbage! This stuff is included with machines as a way to make the machine move around and make...

Thanks!!!!

Thanks! That's what I want, for this Mazak to work like any other machine. I love all my Mazak machines, I don't like mazatrol. So on the offset page for Eia tools there is only one column next to...

Can I set this machine up to use wear comp, I will NEVER use mazatrol,,,,,ever. What I really want to use is wear comp like your first test sample program. Is this possible on this m32?

I am extremely grateful for all your help! I see the G41 on one line all by itself before the first move. My programs don't look like that. I will try this format and see if it works. Om my CAM...

I posted the perameters to show that they are set correctly. Please post a sample program, because my g41 is not using the cutter diam. thank you for all your help.

Picture of my Parameters.

Ok, I did all the stuff you said, everything works but there is a 2.600 inch differance in z offset. I suspect someone added an offset in some perameter. I just offset z in work offset page to adjust...

Thank you! This is probably it. Do I use the Mazak tool setter for anything when using these parameters and using eia?