Search:

Hello I build an CNCmill two years ago and it has been working good since than until today... when the drill goes into the material and The stepper motor gets a little more load it canges direction...

Hello is there any way I can controll a AC-servo with a planet cnc controller? Best regards Flyingpickles https://uploads.tapatalk-cdn.com/20190119/704f58ba4ea368c90aa55ca3b82aed1c.jpg

Skickat...

Hello. Is it possible to connect a liniar scale to the mk3/4 card so that usb cnc gets the info where the milling table is from the scale instead of counting the stepps of the motor. The thing is...

Hello again, yes that would work just fine fore some kinds of operations, the thing is that I want to cut some different patterns and as you said it wont work if I would do like helix cutting and so....

Hello and thanks for the answer. I googeled that but I still dont know what that is. Do you mean that I shall install some kind of fysical mesure equipment on the mill that tell the software what...

Hello I have converted an old mill into an very basic CNC-mill. The thing is that the screw for the table have different backlash on different places. A lot in the middle because it has been more...

Hello. Yes I totaly agree but the thing is that I have to use all of the X range. I dont think it would be so difficult to make. Just ad a section in the program where you can specify how long the...

Hello I have converted an old mill, probably 50 years old or so, to a CNC-mill. The problem is that the backlash is way more in the middle of the screw that moves the table than at the ends because...

Hello I have a question about what file is best compatible with USB-CNC 2.10? I have made an tool path in Artcam that I want to export to USB-CNC. I found out that there where like 340 different...

Hello I try to save a toolpath far a home made mill which i controls with a USB-CNC from Planet CNC.
When I shall save the toolpath I found that there was about 340 formats to chose from... Most of...

Hello, in the motor tuning you can set the acceleration for start and stop of the stepper motors. I want it to start and stop pretty smooth so I set the values for that. But when I load a G-Code for...

YES! That was the button I was searching for, thanks again Gerry! The only problem now is that if I want to go like 5 lines down I have to wait for mach3 to stop on every lines coordinates. The best...

Ok, yes that might be a solution. I did something like this for a couple of years ago. Back then I wanted mach3 just to go to the next line and pause. I remember that I did this with just one mouse...

Hello, I have a g-code loaded in mach3 with 240 "g1" lines (just x,y,z-coordinates) I need mach3 to go for exampel to line five and then hold it and then to line 10 and then hold it and so on. The...

Hello well that could be a way, but I think that would be difficult in my case because I am going to use 8 axis (X,Y,Z) for one computer and pan, tilt, roll, focus and zoom with another computer so I...

Hello, now I have tested your macro and yes it works just as I want it to work so big thanks for that! The next question is: do you know a good way to make the polygon lines with a specific number of...

Hello I am building a camera controller system and shall do a polygon line which I transform to g-code and then control a camera controller system via mach3. My problem is that I need a software that...

Hello the problem is now solved, I have two computers with mach3 and two controller boards. I just shift the two controller boards and then it starts to work, I do not know way but it is still...

Hello I have a system with 5 stepper motors which I control with Mach3. The system has worked good for some years but one day the z axis just wanted to rotate in one direction... No matter if I try...

YES!! it works perfectly. What macro did you use to generate the gcode?

Well you can flipp it If you want it is just
a test to see if it works.

Best regards flyingpickles

Ok, well that sounds good! I hope the .dxf is attached.

Hello I am building a camera controller system to control my dslr when I do stop motion videos. I want to make a path (a 3d spline made in cinema 4d) for the camera to follow. I tried to make a helix...