Search:

This delay has a some LGK plasma cutters. Delay depend from the capacity of the elctrolythic capacitor in the plasma start input. Usually we find this cap and change to lower value (was for example...

It does not matter, because Neuron is full stand alone. CNC controls doesn't even know about the z axis - only XY. Torch Z slide and plasma cutter under full Neuron control.

Correct. Neuron this is a full stand alone THC and require to/from CNC only 3 IO signals - START (M3/M5), THCOFF and ARCOK - it's can be software or hardware signals - both can processed in same...

I totally agree, it's true.
Antidown future implemented inside motion controller and THC OFF output signal controlled in the real time.
Also UCCNC has a nice future for plasma. On the Arc Lost...

This is the new Break Out Board for plasma cutting machines that uses Neuron Simplicity THC.

333116


New design with surface mount components
Easy connection to Neuron Simplicity THC (RJ45...

Yes, ArkOk (XFER) output of the MaxPro200 is open collector 24V/10mA.
We use this schematic for connection Neuron THC to MaxPro200. 12V power supply from controller and small 12V relay used.
For...

I think to add Puddle jump future to the simplicity controller too.
Other Neuron controllers works only with Mach3/4 CNC software. And for Start/Stop signals for Mach3 we have 25 msec max delay, for...

Hello Keith!
Very impressed with your knowledge of plasma cutting. I think you will understand me very good :)
About Simplicity futures, yes it's have Torch refire, Voltage sampling, have THC...

May be will help this post Revisiting those blasted divots... - PlasmaSpider.com
Also any information there are on the Tech Tips topics Tech Tips - PlasmaSpider.com

I think you have to use X and Y MX3660 drivers for gantry (X & W). Z driver of the MX3660 for Y axis. For Z (torch axis) you have to add another driver (for example M542) and use a 4 axis control...

Don't worry.
I think you just have to start. Further there will be all explain :)
This is not difficult. And when you're done and look back, you say - it was so easy.

Leadshine specify this output as maximum 24V@70mA (Power Consumption = 1.5 Watts)
Relay type will depend from your Relay Power Supply.
For example for 12V power supply you can use this relay...

Hello!
I think you have to use external relay for control torch ON/OFF. For example MX3660 has Output3+ and Output3- connectors. Connect external relay as on the picture. Then config in the Mach3 -...

Hello!
CastleWorks, look how work my Neuron Simplicity THC.
Torch slide and cutter under full Neuron control.No makros.
Just use Neuron post processor with THC control rules for sheetcam for...

Hello!
I see on the photo schematic diagram for Neuron THC.
Just you can find more info about cutting process with timing diagram in this user's manuals....

New Full Stand Alone Neuron Torch Height Control (THC) works with any CNC (Mach3, Mach4, Linux EMC2 and other). Controller use discrete I/O interface to CNC and plasma cutter.

More information on...

Hello!
Steven, If you still have interest to find full stand alone THC for replacing the Torchmate red screen controller look: Neuron Simplicity
User Manual...

Hi Nocke!
You don't message me any time and I was hope you solved this problem.
I think you have the problem with RF noise, but we need to find where the noises is penetrate into you PC. And think...

Hi!
I think you have to connect to:
- Cutter start input
- Divided Arc Voltage output (1\50)
- Ok to Move cutter output connect to the THCON input of the BOB
283508
I hope this help you and...

Yes, this lot has full information about connection and setup.

Hi!
It will be great if you give any information about your Break Out Board.

In the proma manual I see that STEP / DIR Inputs and Outputs TTL 5V, 470 Ohm +5V PullUp inputs.

I think - you...

Steven, do you use the red screen or blue screen Torchmate THC?

Steven, ask me - your Torchmate THC has the Input for Initial Height Sensing procedure (find metal surface)? Like float head switch.
Try to check it.
My ohmic sensor has relay output. Maybe it is...

Hi Steven!
Unfortunately Neuron Lite and Professional version can work only with Mach3/Mach4.
BUT Now being tested the new full stand alone Neuron THC controller.
It can work with any CNC and...

I'm sure if you correctly make grounding, then you will not have problems with HV and HF start.
A lot of my customers use similar plasma cutters, including ChinaMade. Proper grounding, shielding and...

That's right.You have to use the M10Px/M11Px command in G-Code to disable/enable the THC without pause in motion.
For example - M11P4 will switch ON Output#4 and the command M10P4 will switch OFF...

Yes Neuron.THC is stand alone industrial Torch Height Controller, connected to Mach3 via 10/100 Base-T Ethernet interface (only programming and IO interface).

Neuron has internal motion...

:)
Neuron Plasma + OxyFuel combined controller is coming soon....

Hello everyone!
I am the developer of this controller and can answer all your questions.
If anyone is interested I attached the user manual.
I think it will help answer many questions.

Neuron.THC Lite is standalone Torch Height Controller, connected to Mach3 via 10/100 Base-T Ethernet interface and controls the Z axis motor driver directly (internal motion controller).

...