What is your control model?
Type: Posts; User: Kittiwat
What is your control model?
Hi,
We can not recovery data if you delete it.
But the tool change sub program is write by user.
I think, Control has M6 for tool change already. For Using up to user.
Hi,
For basic set up.
1. For X,Y axis
1.1 Find the center of spindle and Table move x-210.00mm and y-210.00mm. It is the machine zero point.
1.2 [DGN/INPUT] --> find manu to [ABS-SRV]...
You meaning Compression Spring at Draw Bar set?
How to check clamp force?
Normally if BT40 standard tool clamp force 11000 - 16000 N
Where is the broken bolt?
Please indicate position to...
[email protected]
Please send me about ladder picture too.
Hi,
the bolts that hold the spindle dawgs(ears)
Where is the bolts?
Sorry,I can not imaging.
On detection ring?
Hi,
Are you have Ladder Book?
Normally ladder line of Mori Seiki Vertical machine Alarm EX1024 are checking for
---> No MDI mode + Work memory end M2/M30 + Cycle start
But most machine...
Hi,
What is MAPSS type?
If MSX-850III
The 2nd spindle Chuck timer are #16070-16072.
For easy to check --> the alarm code show on Ladder book, you can see Address of alarm and find it on...
Hi,
Normally machine status.
If power on machine, the signal of Turret clamp will be active.
Check the signal of Turret clamp / unclamp first. (control relay and solenoid valve)
After check the...
Hi,
This massage must be occur when first power on machine to machine ready mode or push cycle start with auto mode on first time power on or after M2/M30 finish before.
I don't sure that, Machine...
If anyone have machine Kitamura Mycenter 3XiF spindle speed 20000rpm.
Please send data about Drawing of Spindle unit to me.
I will try to take off it to repair.
Please help me too.
Thank...
Hi,
My JENN-WEI 42B Lathe have problem with accuracy.
I would like to change bearing of Z axis and spindle.
I would like to know the bearing spec.
Please help me for parts list or spec of...
I have a problem with Agie wire cut machine.
The problem is wire broken when start cutting condition.
Please let me know how to adjustment tension of wire or other solution for solve it.
Thank...
Please help me for AGIE Wire cut : Agiepuls HSS
The wire was broken when start program.
I don't sure because it not alarm.
I test it by no cutting only feed wire and start current cutting....
Hi,
Lathe machine Leadwell LTC-15 Fanuc 0T (parameter 0~9xx)
Parameter loss.
Can you sent me for parameter list or not?
Please help me too.
My e-mail : [email protected]
FANUC A16B-1010-0190/05B
What model of your MAPPS?
4 Axis ::: APC ?? or ???
Hi.
Mori Seiki Machine MV-65 with Yasnac MX3
This machine last time can use interface link between machine and PC for run program on PC by T mode.
This machine stop for repair machine about...
Thank you Guhl.
This machine don't have this parts.
Mori Seiki Machine SL-25B Control Fanuc 10TF-A Alarm J on mother board.
The CRT dark when power on. I see alarm on mother board show J
Alarm Code : J
Description: PC or interface converter not...
Hello,
Can you help me ?
I have the second hand machine Leadwell LTC-15 Year 1988 Fanuc 0T
Machine parameter loss.
Please send me for manual for Fanuc 0T or Parameter lists....
Hello, My name is Kittiwat, Nick name is Ben
Nice to meet you.