Hi there, try to reduce transferring speed rate and finally Gatter earth wires to one poind to ground. Also check if the your system version is supported the relas4d updated framework for your new...
Type: Posts; User: Russell840
Hi there, try to reduce transferring speed rate and finally Gatter earth wires to one poind to ground. Also check if the your system version is supported the relas4d updated framework for your new...
hi there
I reinstalled a Gildemeister GAC65 series month ago after 8year maybe.
after the machine comes up and reloading the CNC parameters when I want to
go to REFERENCE-Point;
The machine sees...
I have Some Books.
The reason was " Machines Parameters was Corrupted" needs to reload and set SPS Switches.
Dear Marco, Could you explain what is your mean?
Regards :-)
Hi there
Dear Advanced
I have a Spindle Drive, Which is explored without any electrical schematic plan.
unfortunately, I have no data and document to assemble IJBT, Capacitors and ... on the...
Dear Sir or Madam,
I’m looking for a CNC/PLC Machinery challenge which keeps me involved with latest Automation technologies, Controller Systems, Digital Measurement and computerization and let me...
Hi there
Dear Sir or Madam,
I’m looking for a CNC/PLC Machinery challenge which keeps me involved with latest Automation technologies, Controller Systems, Digital Measurement and computerization...
here is the 2nd connection, Gray & Green.
Hi there
What I want to ask is about Spindle Drive, which is:
KDA 3.2 series.
when I connect the " Control Voltage Bus ( X1 pin assignment 16way bus ), unfortunately, the power unit stop...
Well, I am repairer and need to translate punched tapes to export the old machines parameters and machine Data, sometimes PLC. It's sometimes floppy disk, 5inch, 3.4 inches, punched tape,
It is...
you need to read the manuals and the parameter explanation to set the drives parameters.
It's not too hard but sensible, you need to care what you are changing.
With Regards
Check the machines Earth and 0 Volt, also
Phase Sequence is matter.
regards
Russell Dolat
Hi there Dear bako85
Ok, no problem. here is my mail address, send me an email.
I'll send you some backups for you. [email protected]
also, you need PCIN and better to have a Windows XP PC, I...
Hi there
I am working on a Gildemeister with Eltropilot EP8-S Controller. unfortunately, I have no document and manual of this System Controller.
Well, I just want to ask do you have any data...
Do you have any backup of it? It seems you need to reload the Controller.
Also, I have Some printed page, Which contains the backup parameters and I have to enter all of those by hand!
Does...
Hi there
What I want to ask is about:
Replacing the MitsubisheMeldas 300 Spindle Servo Motor With a Delta C2000 One.
Is It Possible?
Regards Russell
Hi there :-D
I make solve the problem, Some Capacitors Didn't works well.
Regards
Hi there :-)
I'm working on a Gildemeister GAC65 lathe, and I have a problem with one of my axis Servo Drive " TDM 3.2-20-300-W0".
I connect power, and truth give feed command with my multimeter...
Hi there
You can edit your ladder file in the system controller, also you can edit PLC Parameter at Parameters setting.
If you want to have a ladder file, depends on the system controllers...
Dear Mr. Dawson
I test 19600 but the same problem is here. i also testes "SSS Mode Parameter Setting" Para: 8000/ Para 1132 , Para1258 . But there is the same problem and I need to test again to...
The baud rate is 4800/databit 7/parety chek even, stop bit 1, same on PC and Controller also cam software.
I try to 1148: 1 with/without G64 and 1148: 0 with/ without 1148.
the only difference...
Dear Mr. Dawson
I test the program with G2 & G3 but there is no difference and the problem is the same.
I think the problem is in 1148 series parameters also I need to modify some of the...
Sorry, the picture is not Clear. I send the PDF document.
Pages 188-192
Hello Dear Mr. Dawson
We use " Power-Mill 2017" as Cam program and yes, the CAM program creating circular moves as line segments.
Unfortunately, I can not find the setting place in my CAM program...
Dear Mr.Dawson
let me try tomorrow morning and I will tell you the results.
have a nice time
Sir, thanks for your response but the machine works as well with internal memory at 7000 feed, but when want to use tape mode, it doesn't work more than 1600.
I think the controller can handle the...
Hi there
I am Russell, a 27-year-old- Hardware engineer, Who love technologies and system controllers and robotics.
I install controller system, Repair, troubleshoot and retrofit metal work CNC...
If you have the backups of machine, reload the parameters.
it would be helpful.
regards
Hello Sir
Please contact me and explain more with picturs.
[email protected]
With Regards
Russell