523,794 active members*
1,108 visitors online*
Register for free
Login

Search:

Type: Posts; User: slidingheadman

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    63

    Re: Alarm Z09 remote io m32 help

    Remote I/O alarms are from the HR371 card
    On this machine you will have 2 in the NC unit and depending what is on your machine you will have some on the IF card in the electrical cabinet check that...
  2. Re: Meldas 600 m32 citizen y02 alarm system 0051 0001

    Y02 system alarm is not good
    The NC system has seen a fault with 1 of the intelligent servo systems but its not sure what one it was
  3. Replies
    2
    Views
    74

    Re: Spindle will only go so fast

    If its the sub spindle the speed is set low if the chuck is not closed if its the main spindle try running this spindle in C axis if it alarms out possible the PLG needs to be replaced
  4. Re: Citizen M32 2002 C axis indexing not work

    Has the option for main spindle C axis been switched on check in the machine structure page
  5. Replies
    1
    Views
    346

    Re: C?T?ZEN L20 START PROBLEM

    In the back on the NC unit is a 7 segment display this should be on 9 if not possable cause is 1 a push button is stuck in or 2 the hdd is not running
  6. Re: Citizen M12 " Cannot download NC system" Alarm

    Time to get the wallet out this is a HDD fault new drive needed
  7. Re: need help citizen M-32 LATHE ´´ OVER VOLTAGE´´ ERROR

    You have a short on the 24v dc this is normally the wire to the X2 brake clear any swarf from this area long term the cable will need attention
  8. Re: Citizen cincom B12 449 A3 Axis: inv. IPM Alarm

    Letter A on the servo drive is a parameter has been set wrong
  9. Re: Citizen Prep page, increasing diameter value

    Use man set and increase the dia value
  10. Replies
    4
    Views
    1,579

    Re: Alarm Code Swiss Cincom L20

    This alarm is the servo backup battery's these need to be replaced but for now leave the machine powered up with the alarm for half an hour then power off and back on you will then have Z71 alarms...
  11. Re: Mitsubishi Meldas 500 alarms on citizen

    The problem with this machine is the EX001 alarm until this is cleared you will have the emergency alarm
    The problem could be the thermal trips these are located at the bottom of the contactors the...
  12. Re: Citizen M20 Slidinghead - with Maldas 500 Control

    This is a option and you need the code to switch it on
    Then where you enter 1001 tab tab M you need to enter 527 tab tab S this then gives you a option page in the parameter screen
  13. Re: Need Help Fixing/Setting Up Citizen E32 - Willing To Pay

    Hi
    First have you got the original parameter list
    If not contact Citizen with the machine Ser No and ask for it
    If you have lost the parameters out of the machine is the NC Battery OK if not...
  14. Replies
    2
    Views
    117

    Re: Z70 Abs. Data Error 0001 Z1.

    Z70 is a zero return alarm
    Zero return all axis the only one that could be a problem is T1 there is a procedure for this if you need it
  15. Replies
    4
    Views
    241

    Re: Relocation Detection Device

    Ask citizen to change the movement detector to the newer version
  16. Re: Setting reference postions Citizen K16

    What you have been told is correct this stops the need for switches
    To change the axis position its the same as any Fanuc parameters 1850 for the grid shift and 1815 for the APZ
    When zero returning...
  17. Re: Cincom L25 Y02 alarm 0051 003 , need parameters too

    Hi

    If you are on an L520 with a 600 control you can restore the S ram and para file from the back up and restore function on the control
    The y02 51 alarm is a servo problem

    If you need these...
  18. Replies
    4
    Views
    1,031

    Re: Citizen L32 axis servo alarm

    No as the re gen resistors for all axis are located at the right hand end of the machine under the perforated cove below the barfeed so changing the drive to another one will be the same as the...
  19. Replies
    4
    Views
    1,031

    Re: Citizen L32 axis servo alarm

    Hi

    Your problem is the re gen resistor on the servo amp check the resistance of the wire P to N think it should be 40 ohms but check with one of the other drives all the re gen resistors are the...
  20. Re: Citizen c 16 pulls stock back awau from cutoff rool

    Yo

    On the relay board there is a Omron relay this can be found by looking at the board and get someone to open and close the main spindle chuck
    This relay sends the signal to the bar feed change...
  21. Re: Citizen L20, monitor and keyboard not responding

    On this site if you go to Meldas 300 problems I found a good procedure for rebooting and loading all the data
  22. Replies
    3
    Views
    2,374

    Re: CITIZEN L20 VIII ALARM

    Bad news

    This will be a new hard drive this alarm is one of the windows files has been lost or corrupted
  23. Replies
    5
    Views
    1,508

    Re: Citizen M32

    cogsman

    You are correct do not adjust the switches
    If the procedure from Citizen will not work the span ring on the last gear has moved
  24. Replies
    3
    Views
    1,830

    Re: Citizen B12-6 Alarm Messages.

    Hi

    All these alarms are caused by the machine 24v dc shorted to earth from your pat off probe
    Disconnect the part off probe from the relay board and all will be well
  25. Replies
    1
    Views
    97

    Re: Citizen Cincom F-12

    Hi
    On this machine it will usually be the shot pin in the top turret or bottom turret not in the correct position at power up
    With the machine power off remove the small cover and push the shot...
  26. Replies
    0
    Views
    24

    New here

    Hello have looked at this site but have only now become a member
    Have worked on machine tools fro an apprentice now at 50 that's a log time
Results 1 to 26 of 26