Search:

Does anyone have a .dxf file for a knife any style will work.

Jeff.

thanks for the file. if i get it done, i will most certainly post it.

thanks.

thanks mactec54 for the info. the unit we have is not from Deublin. its a Haas part.. there is a bunch of parts that came with it. a small regulator and some hoses and an electrical jumper wire. it...

i recently purchased a bearingless coolant union, as we have gone thru a couple of the Deublin unions in the past and wanted to try something new. Sirco didnt say this was a service technician...

we have noticed some noise when running the machine in low gear and low RPM. i removed the belt fro transmission to spindle, and the problem seems to be in the motor/transmission area. i have...

I noticed some ball marks on the pull stud from our VF-11, and i am not sure what would cause this to happen? i have replaced the pull stud for now, but i think there may be more to this problem then...

@fordav11 i am starting to loose my patience with this turd. now we have started reassembling the machine, and trying to index the turret, we get error 1783-01, turret unclamp time over A side 1, i...

thanks @fordav11.

would you be putting anti seize on all parts when reassembling?

@jason_alex.

the gantry is mounted over the slagger table. i found that the master drive motor was pulling in nice and easy to the meshing gears, but the slave axis had to be manually bumped...

thanks Matt@RFR.

we have made a couple pieces for the cover, and are getting ready to install them. i have to lighten them up a bit, and put some lexan in the cover to allow a bit more light into...

we got the turret removed, and down and the clutch removed. now i have to remove 2 bent tapered pins, and the manual says to ream out the holes??? i guess this is a judgement call, depending on how...

we had a crash last night on our Captain L370, the tool indexed and hit the part in the chuck at full speed. today i put in the pins, and my dial says its still out over .010"... i guess i have to...

We are using a TSC1000 on our VF-11, and we have tons of coolant spraying out of the machine. we have made a light duty cover in the past, but i am wondering if anyone has ever built an aftermarket...

thanks torchhead. good tip.

anyone have a 2D .dxf file of the toronto blue jays????

i am looking for 2D .dxf file with the toronto blue jays logo on it. i would like to be able to burn it out of steel.

Has anyone devised some sort of chart that a person could follow in order to fine tune your machines overall cut quality? we are having some issues with general appearance for the parts being put...

thanks Jim.

Thanks Phil.

I found an air cylinder leaking a severe amount of air on our turret, and once we repaired that, it seemed to have enough air to shift the gears. no problems since.

thanks.

has anyone built a holder to attach to the torch receptacle to be able to trace out the part before actually burning it? or is this something you can buy? i would like to have a tool like this to be...

we have a Metal Master Plus, and recently we have been getting lots of terminal faults, for example 5202 DRV fault on drive amp (Xa), and 5625 HL1: cnc kernel drv error, and 5627 HL1: error executing...

thanks jimcolt.

i am looking for some cool 2D .DXF files to run on our burn table. mostly i am looking for a mustache for Movember.

thanks, i dont know how to delete the post. i have allready posted this question in the other forum.

We have a HPR 260 manual gas console, and recently it started smelling like ozone during operation. I have to assume that we are dealing with a leak. I have been unsucssesful in locating the leak....

We have a Hypertherm HPR260, with a manual gas console, and as of recently i have noticed that the unit is throwing off quite a bit of ozone smell, but only when the machine is running. i would have...

I have a Haas VF-3 40 taper, and I am looking to take the gearbox appart to see what is wrong with the gear shifter assembly. I have taken appart the solenoid valve to check for any obstructions, I...

thanks haastec, i will try and open the orifice a bit more, another quick question, would the cylinder rod that the runs the gear between high and low, ever get gummed up, not allowing the cylinder...

on startup, the mill tries to shift between high and low gear, and eventually faults out, generating either a 117 spindle high gear fault, or 118 spindle low gear fault. I have taken off the solenoid...

we ended up changing the magnetic encoder, and reset the spindle orientation, this seems to have solved the problem.

thanks.