502,814 active members
4,647 visitors online
Register for free
Login

Search:

Type: Posts; User: Yellowhair

Search: Search took 0.00 seconds.

  1. Thread: Micro Shop

    by Yellowhair
    Replies
    4
    Views
    174

    Re: Micro Shop

    I love it, and I could have an in build sawdust filter. Nice one.
  2. Thread: Micro Shop

    by Yellowhair
    Replies
    4
    Views
    174

    Re: Micro Shop

    I need the hat, it is somewhere to keep my pencil and eye protection, I just need to figure out how to hang my ear defenders from it.

    Best regards
  3. Thread: Micro Shop

    by Yellowhair
    Replies
    4
    Views
    174

    Micro Shop

    Hi everyone, when I look all the space you have in your workshops it makes me so jealous.
    I have a 7x5 garden shed in which to house my 3020 cnc and other woodworking essentials,
    table saw, planer,...
  4. Re: 3020 Chinese power supply needed / can I get the bits to build one?

    Hi John, all I can say is you are a STAR. The new FET and NE555 chips turned up this morning so I soldered the new FET in place, tested it and everything WORKED without even having to solder the new...
  5. Re: 3020 Chinese power supply needed / can I get the bits to build one?

    Hi John, what I have done is ordered a new FET and a new 555 chip I am hoping that after a bit of soldering this weekend I should be up and running again.
    I will keep you informed of any progress...
  6. Re: 3020 Chinese power supply needed / can I get the bits to build one?

    Hi John, I have tried to do the tests you asked and if I have done them correct then the results are:Across fuse 1 I have a reading of .025
    across the the 1 ohm resistors it is 0.00 this is with a...
  7. Re: 3020 Chinese power supply needed / can I get the bits to build one?

    John I'm so sorry I fear I have lead you down the wrong path, you see the spindle is running at full speed all the time, as soon as the power switch is on, and there is no difference when the spindle...
  8. Re: 3020 Chinese power supply needed / can I get the bits to build one?

    Hello again John, the physical board size is 12cms x 5.5cms.
    Thank you for the other information but I have no idea what it means, sorry but electronics and me don't mix.

    Best regards,

    Custer
  9. Re: 3020 Chinese power supply needed / can I get the bits to build one?

    Hi John, the FET was disconnected at that time ready to solder a new one in place.
    Here are some more photo's.
    Many thanks for all your help.
    Best regards,...
  10. Re: 3020 Chinese power supply needed / can I get the bits to build one?

    Thank you John, I will get some further information together: In the meantime here are a few photo's of the suspect board. This power supply let me down before and I replaced a mosfet chip and it was...
  11. 3020 Chinese power supply needed / can I get the bits to build one?

    Hi everybody, totally snookered, my Chinese 3020 power supply finally gave up the ghost yesterday and is totally beyond repair.
    Is there anyone out there that has a power supply for the 3 Axis...
  12. Replies
    5
    Views
    310

    Re: Mach3 puzzle???

    WOW Gerry, thank you very much, I completely missed it when I looked, but to be honest I had no idea about that in any event. You are an absolute star, I just hope that I can play a small part in...
  13. Replies
    5
    Views
    310

    Re: Mach3 puzzle???

    Hi Gerry, I went to the General Config but I have no idea what I'm looking for, I can't seem to find what you are telling me about. Sorry but could you explain more to me.

    Best regards,

    Joe
  14. Replies
    5
    Views
    310

    Re: Mach3 puzzle???

    Thank you for the fast response, I will go and give that a try.

    Many thanks,
    Joe
  15. Replies
    5
    Views
    310

    Mach3 puzzle???

    I wonder if someone could help me with a puzzle I have. I have created a memo board in ArtCam, saved the tool-paths to Gcode, then loaded it into Mach3 with a config file for a Chinese 6040 cnc but...
Results 1 to 15 of 15