Search:

I need to get a bigger cutoff tool but the Iscar/Hertel/walter ones I look at need the 25MM holder - all us St10 people have 19mm or .750

can I just cut the bottom to .750 and will tool be on...

My quirk with Haas Graphics - as crude as it is I wish it had an an isometric view...... Lots of other machines - OLDER machine have it. I had an Okuma in the 90's that had great graphics. Mazak -...

We want a Haas TM-1P enclosed with 10 station tools and 6K spindle.

Can you use a standard 6 Inch vice on these? (Kurt D688). I was doing calculations from machine diagram and it looks close to...

Our renishaw OTS is giving us problems. Had to replace the breakaway and re-level probe tip from a toolsetter problem with another worker. I went to do recalibrate program and it would not search...

Superman..... you saved the day!!

I don't use sequence numbers and want to output N# = Tool #
(makes it easier to search without bumping into tool pre calls )

I think I would have to get rid of all the n$ in the post first - but...

never mind - I just moved the OTS to where I wanted - duh.....

I think the probe cal program also resets that position

We have a Mazak 510 with Renishaw OTS tool setter. We need to adjust the XY location of the auto setter. I don't have a program manual and which program needs adjusting.

Thanks

Bang !!! that works - I changed from cutter rad to constant and I get z rapids. I also see how it will stay down if you want.

Thanks - - Now I understand

"When the tool finishes one pass...

I have identical operations - face mill - very simple.

First one has Z1.0 rapids like I want - 2nd one doesn't rapid up but just feeds back across to start point and then does next z minus step. ...

This doesn't work for me on m post

"(" {Date} " " {Time} ")"

I even tried - Replace "*" With "(" {Date} " " {Time} ")"


StartCode # Start of the program ...

I'm aware the DSN needs the ICD. I was told by another programmer that if I regen each op that might work to recreate the INC.

I am now converting to Velocity .scrpt on some of our older files...

funny thing is that i can post my previous version (a) of the same dsn file. and it posts fine and there is no .inc file in the NCD dir.

I think I made a mistake and may have dumped the .inc file associated with the dsn. How can I fix this? I thought that it created a .inc but there must be something telling it was there previous. ...

I need to find the block skip switch in Anilam 6000 (Fryer) or how to hook up an Op Stop manual switch ( I guess this was an option on these according to the manual )

need corner round tool in library - I don't see any thing for standard corner rounds or custom tools. I use chamfer mill with same hub dia. but would prefer a CR tool

All fixed - thanks !!!! ( I feel like a dope about the B axis clamp command )

we were able to clean the pads while we had it in that state. Yes its the MF-M6 control.

:banana:

In case anyone else has this problem.

m88/m89 id/od clamp

1) key on
2) m code - cycle st
3) press and hold pedal
4) press reset

we were changing pallets and had a power outage with our MH-40 and M6 Fanuc control. as the pallets were swapping they finished the swap.

We powered back up and use the manual APC command page...

I am using generic Haas 4x to output code with X5 and it is almost spot on.

I do need to output G84 feed rate as IPR and I can't find a toggle in tool setup or maybe variable calculation in the...

never mind i found it on older post F9

I have these system origin crosshairs that are visible on the screen. (They weren't there last week. ) How do I turn off or change size?

We have a MC-50 Fryer with Anilam 6000M. We are getting a fatal error

Motor - 4 not moving at MAX motor power
fatal card error
Time out in finish sequence

Any clues and we could use the name...

We need the procedure to switch from external clamping to internal clamping.
There is NO switch anywhere.

The Haku book states" Select chuck clamp direction, change by MDI, while memory...