If you want the endmill to last and want to be able to run unattended go with the adaptive.
I have slotted in 303 before but it's hard to get the chip out.(w/ air blast/mist or flood) so don't...
Type: Posts; User: BIRDTOOL
If you want the endmill to last and want to be able to run unattended go with the adaptive.
I have slotted in 303 before but it's hard to get the chip out.(w/ air blast/mist or flood) so don't...
I think I remember reading an old post by a user rsdi? stating u need to change the network ip address to something like 10.10.10.1.
You need to make 2 chains, inner and outer profiles. Select the outside chain, create a pocket feature(from 2d mill bar), under one of the tabs there's a box to pick the island(pick inner chain). If...
I believe its as his machine setup, his z-axis is in home(light on button is on) G54 is set at zero in this position and his tool length is zero according to the pic.
Our shop has a TF25 lathe that is getting slbus errors on bootup. They used to be able to shut it down an restart and it would be good to go, now its stuck. Any help on where to start looking would...
I bought a series 2 5-6 years ago for 5500. Non Atc/pdb. Came w/ a bunch of holders,vise,stand. I'd say you'd be in the 8-9k but if u start higher u can always go down.
Check your parallel port cable and/or re seat the mesa card inside the pc.
(currently has a major problem in one lead screw)
Bob is your hurco direct drive from the servo? When ours experienced your issue it was just the belt between the servo and ball screw.
https://www.amazon.com/RATTM-MOTOR-Handwheel-Emergency-MITSUBISHI/dp/B07CZ7F3Y3/ref=sxts_sxwds-bia-wc-drs1_0?cv_ct_cx=100ppr&dchild=1&keywords=100ppr&pd_rd_i=B07CZ7F3Y3&pd_rd_r=420ec195-d191-476b-95e7...
Tormach already has a "real" pendant on their fancy $2k control, it appears to be the same one on Amazon for $75. My guess is the code is already in PP, it may just be a matter of setting up the...
I just looked at the MX at Fabtech, the pendant is hooked up via a parallel port. I also did notice they were running PP version 2.4...
Our shop is looking at a new 5-axis Mazak 500/5x. Can anyone offer user experience with these machines/manufacturer/control? We only have Fanuc in the shop now. What other machines manufactures would...
Here's an option that may work for you:
Element
Your g-code does reflect the tool offset. Look at lines 660 and 730. y positions from -.4103 to + 1.7972 = 2.2075 (-.500 for your cutter)= 1.7075.
If your cutter is not exactly .500 that would...
It backplots "ok", would help to see a dimensional print or know much comp you are using.
Try splitting N175 into two lines, first move N175 X1.5 N176 Y1.25
Next would be give it a different H...
Check your parallel port cable didn't come loose.
You can get oring cord that is 1/8"(.125), check MSC 65076499.
Just to ask, you do have the "manual tool change" button selected under the settings page?
I feel the OPs original post had to come from having a new toy and not being able to play with it(yet). It certainly would be in Tormachs interest (from a sales point) to "review" a new (customer)...
Google "craftycnc"
Reseat all your ribbon cable connections, make sure you don't have a bent pin on the parallel port bulkhead connector. Mine was loose once and it acted the same way.
Funny this thread started as we have a 3yr old Leadwell 40it that just started getting the same alarm 2/3 weeks ago. We were running mold cavities that required a lot of drilling and had the rapid at...
Shut off the "smart toolbar", it resets the other tool bars on your screen. I think its under options and just uncheck the startup button.
It was intended to free up screen space, but who needs...
Can u just use their i/o usb add-on? 32616 - USB M-Code I/O Interface (if it was in stock)
Probably need to follow Linucnc rules, (no M98/99)
m
Maybe something like this:
G90 G40 G17
o1 repeat [10]
G0X-1.49Y3.20Z.75
x16.05y-6.43z9.9
o1 endrepeat
This should give you want your looking for.
https://www.youtube.com/watch?v=1XTcXOFnPLo
I downloaded 2.7 last night and ran the live version, there were setup templates listed for the Tormach pcnc machines.
I think in the end PP was the "cheapest" option for Tormach to do, take the...
You can break up ea tool as a separate sub program if needed
G52 shift as long as your not using more than one fixture offset(it moves all). Your current program becomes a sub program(remove any fixture offset calls), main program uses 1fixture offset,say G54...
I've been doing cadcam for almost 17yrs, primarily with pro/nc but have tinkered with a few. The shop I'm at now uses esprit, if you go that route just get the cds from thecamwizard.com. very...