Search:

The one issue is that DXF is not really a standard it has been changed many times. It could be a problem with points not lining up there is a parameter in the control to bridge the gaps in the lines...

If you hit display error what is your following error wen the machine stops?
The problem maybe the axis is not in position.

go into handwheel and move the axis to the position you want o be zero then hit g54 button for x and y

Then the software should be on ERPOMS.
you may try and reformat the software

what version of control?

http://www.shopwareinc.com/mill-verX.html

go here and look for the mpcent6 post cent 5, 6, and 7 are all the same for the posts

Grid is the same as home. Should be pin 10 on the axis plugs
limits go to terminals 6, 7, 8, and 9

If you move the turret with a wrench ok then i would say the motor is bad if there are some hard spots when you are turning it then you have damaged something in the turret like a gear or bent shaft

Are you sure you have all 3 phases it sounds like you lost one.
double check for from phase to phase to phase on the top side of the relay you should have 220v across all 3. if you have it there...

take the little end cap off the motor there is a 10 or 12 mm hex that you can put a socket on and index the turret buy hand if you can turn it ok then in MDI do a M20 this should index to the next...

The limit switches go to terminal block 6 7 8 and 9
unhook the wires and see if any are shorted to ground terminal 6 to 7 is the X axis 7 to 8 is the Y axis and 8 to 9 is the Z Most likely the X or...

after you replace the battery you will have to hit display stat 9 then the CE button. then reload the parameters.

Try and hit the tool change reset button if the spindle works after that then you have a limit switch shorted to ground

You will need a shield cable and 25 feet is fine

here is the rs232 info

No you do not need it. They only use air at tool change they must have had air volume problems in there shop

Yes that is an option through Milltronics.

If the head is moving down the home switch maybe stuck in. you can see this on the diag screen hit display diag then z for the z axis on the left side look for home switch it should be a zero until...

should be 500 count with quadrature is 2000

M32 tells the control to wait for the wait channel

The pocket clear is a can cycle you do not want the mill start and end.
just remove the start and end mill cycle.
Make sure you have the pocket mill setup

Here is a link to program examples I had posted before.
http://www.cnczone.com/forums/showthread.php?t=25609&highlight=mholden

The programming is very easy on the milltronics.

You can use...

They are Accroloop and the Machine software is DOS based.

The software is Milltronics.
what happens if you unplug the X axis plug and hit reset?
The axis should sit still or drift slowly that will let you know if the Arature and tach are in phase. If it...

The memory size on a cent 5 with the older system is about 100k that you can run a program. but you can DNC the program from memory or load it into the ram or rs232. The editor is the limited so if...

You could try profixrepair.com they also fix drives of all types

I do work for Milltronics.
There should be no change at Milltronics. The company is staying intact as is.
The old owners are still here. The new owners are a family company, LDI is the name. They...

Milltronics has lost a power supply on our phone system we hope to have it repaired by noon

Yes, if it was in english, I think he was asking about if it was programmed in metric

If you are using conversational programming it is asking for threads per unit.
English 1/4 - 20 you would put in 20 for the treads per unit.

If in metric 6mm x 1.5 = .6666 threads per unit....