I just had some over current alarms, we traced it down to a encoder signal. The back bearing of the spindle was picking up runout under load, it could run to full rpm without load, but would fault...
Type: Posts; User: hacdlux
I just had some over current alarms, we traced it down to a encoder signal. The back bearing of the spindle was picking up runout under load, it could run to full rpm without load, but would fault...
A groove tool is a form tool, a threading tool is a form tool,
I use step drills and form reamers semi regularly, and I do have a few jobs where I use external form tools
Most of the time I can...
Its just a difference of terms,
I have edge barfeeds(based on iemcas) on tsugamis.
With the cutoff/stop out of the way
Torque on is the mode where the bar feed is pushing when the collet is...
Another one if your not dead set on a haas,
I have a Hyundai kia skt- 21 lms(long bed, milling,sub)
I see them every now and then in the price range your looking for.
Mine has been running 3...
Just to clarify, the bar should be hard enough the cutoff to where it does not move when the main collet opens.
Think of it like throwing a punch. If my fist is up against you then all I'm going...
Make sure your barfeed torque commands are correct, try increasing feed torque, add a dwell after collet open, make sure collet isn't hitting collet, make sure bar is out of guide bushing before...
contact rem sales if your in the states, also for a few years they have shipped a usb drive in the front control cabinet
schmolz is great stuff,
emj has a division called rgm, also great stuff and they have a precision cold draw that runns right there with ground stock
aluminum i always ran kaiser cold drawn.
most...
It sound like you have subcontracted your services to another machine shop--- Guilty work is slow with the "rona" going on, do what you have to do to pay the bills.
I do make tooling...
I order my pickoff collets ground to size, in that case it is a .365 diameter in a. 365 collet
I also adjust the closers on every job, the problem is when you drill out the material the part...
I am making a 316 tubular part with a thread in the middle,
I am having a problem with the drill on the sub spindle wanting to push the part when 8t gets just the slightest bit dull, the owner...
i have seen sub spindles twist from collisions before, you can also twist the rails but that is less common. check for twist by taking a known good collet and precision pin and check for...
i use esprit daily, on swiss, millturn, and mills. i will say once you have a library of processes built and you have a set strategy you can post code that is ready to run. i have a few personal...
ipm is intelegent power module(or something to that effect) it monitors current and voltage applied to the motor. alarm on the drive will be either a,8,9 it tells you which axis is affected. i have...
i dont have an lt, but i have run into those errors before on my lb3000myw , spindle speed must be in g97 to change from a g140 to 141.
also y, and c axis cause similar errors
Shop Doc – Chatter while turning on 20mm Swiss CNC Lathe | Today’s Machining World
i will add that guide bushing tension is alot of personal prefrence too, when i ran alot of aluminum we would...
i actually have a recool in production now, we are running a 3/16 15xD drill in 316ss with a double ended live holder in our new tsugami the hardest part was figuring out the plumbing but rego was...
i am trying to run some headed pins out of 1018, and chip control has thoroughly eluded me
material is 7/16 round 1018
part has a .248 shaft 1..2" long with a .190dx.200w grind relief under the...
i had a similar problem when there was a chip in a coolant pump plug, we couldnt clear the alarm because the contactor for the pump had actually welded itself closed. you might want to check that the...
m101 and m102 are high pressure coolant codes
its interestin though my y axis displays all the time.
there is an option called "off center turning" you might be missing or its a parameter...
okuma lb3000 myw osp 300 circa 2015
(SUB SPINDLE DRILL)
N5 G141
G00 X30. Y0. Z15. T1100
N5 T1131
N5
G97 S2109 M03
M08
something like this
https://www.youtube.com/watch?v=pd98w41RZpQ
the tool call for a double stack is the same as long as you call y0.
put the y offset in the y off set position.
you have to turn on the y axis to jog to centerline on the presetter, then turn it...
use a standard er collet for milling, sealled colletts have less slots and less grip. also torgue wrenches are cheap insurance, er32 is 100ftlb is hard to get with a standard spanner. but for us any...
thank you gentleman,
im going to get a left hand single point on order,
i just sent a reguest to landis for their ez rollers
and my operator just came in to tell me the single point insert blew...
swiss machines are not necessarily the best for roundness or concentricity. if you want to get your concentricity up bore your collets true to center line. i had to make some .078 pins before i had...
i have several jobs in my shop that are basic tierods. its a long running job
example: 1/4" bar with 1/4-28 thread x .500 long each end from 3-13" in length in 316 stainless
machine is a tsugami...
i just took delivery of an ss26 and am in the process of tooling it up now, all was well until i found a tidbit in one of my catalogs.
the book said not to use internal boring bars(20 mm round...
we have both, we were considered a mori shop for many years, have had the okuma m560-v 9 months. you have more memory, power, rigidity on the okuma. we have another okuma coming friday
I ran a tsugami ss on mastercam x3 at my last shop. i built the post(which i no longer have) it put out pretty good code.
things you need to change for a swiss.
- z axis multipliers in the post....