Search:

Ken,
While I am disappointed in the quality and service, I went into the sale with a mitigation plan assuming I may have to fix problems… knowing this in no way releases XYZ and XYZ USA...

My Z axis is still jacked up... I gave up on support from the OEM! It must be noted that the control card is jacked up also... The letro card excites the laser at start up and fires for a moment.......

Laserdude
XYZ tech should have their assertion pulled from the FDA...
My door interlock has never worked!
Very dangerous....
Should be forbidden from importation...
HO-229

Key motion control element must be non China:nono: (control card, drivers, and steppers/servos):nono:
Mechanicals can be China:stickpoke
You will most likely not be able to obtain the Maytag...

It would appear your laser carriage is trying to go beyond the programmed soft stops… (Step error?)
It would appear your references may be jacked up… I have the same issue with my Z axis. It does...

Focussing lens
Focussing lenses should be kept clean! A dirty focussing lens absorbs more laser radiated energy, heats up and deforms. A deformed lens changes its focal length and the focal...

Ken,
I feel your pain friend… You have captured my thoughts on XYZ-TECH to the letter!

There are watch makers and there are Time Keepers… XYZ-TECH is a Time Keeper and it is my belief they are...

So far Leetro has answered the mail; I have requested the setup procedures for the card. It is my hope they provide this data/answer the mail.
My position on this matter is establishing a second...

Richard,
That is the very crux of my issue; it is unclear to me on how to access these settings from the manufactures manual.

If I had an instruction set or knew the location of said interface I...

Have the 6575 card now; it’s been two months from the time I installed it and the machine is still all gooned up. The best I can figure is the control card settings are not set properly. Tired of...

Do you have the interface software that is required to set the parameters for that card or know where to download it?

Looking for laser control card manufacture that supports AC servos; preferably something that can be setup by the user with minimal effort and without having to contact someone overseas.:drowning:
...

Still broken,
new issues... no clear path forward?:stickpoke

Bonedoc,
Please standby before you spend your hard earned money on XLAS… please watch and see how long it takes XLAS to make my pending issues right… then make your choice. I just received...

Watching with interest Ken... Hope you find resolve quickly!

Hmmm...:violin:

5.2.2. The tuning is very much motor/machine/encoder dependant. There is no universal procedure. Before you start to tune drive you should mechanically disconnect motor from the machine and you...

(wiki) Power transferMain article: Maximum power theorem
Whenever a source of power with a fixed output impedance such as an electric signal source, a radio transmitter or a mechanical sound (e.g.,...

How does your PID settings look… I would speculate your stepper motors are oscillating at rest a fraction of a degree?:rolleyes:

Many issues have been discovered upon initial operation of the machine purchased... these issues could be sorted out quickly with proper technical support.

Would anyone like to see the timeline,...

Many issues have been discovered upon initial operation of the machine purchased... these issues could be sorted out quickly with proper technical support.

Would anyone like to see the timeline,...

(WIKI)
Sparks in air
Long exposure photograph of a Tesla coil showing the repeated electric discharges
The dielectric breakdown strength of dry air, at Standard Temperature and Pressure (STP),...

Thanks for that wonderful data, I considered the 150watt Reci tube but was not 100% sure about the ability to engrave well at lower power settings.

Something I may have to revisit upon sorting out...

Cinematic2... Please elaborate on your blanket statement… You have everyone’s attention! :stickpoke

Dave

While no expert on the matter, within the cut software currently utilizing is a parameter for cutting and engraving holes, it would seem the software adjusts (slows down) and in doing so achieves...

Good Morning do-it yourselfers,
I am seeking a good book or thread on setting up a 2 axis laser cutting and engraving machine…
Background:
I recently purchased an XYZ-TECH laser with very nice...

Things did not exactly work well to say it lightly! Holding my breath and waiting to find out if XYZ-TECH has what it takes to make it right!:boxing:

Have an EXLAS Laser... Let’s just say it has serious motion control issues… The jury’s still out weather the customer service department will promptly fix the issue!(wedge)

After several months of negotiation and research I purchased a laser… It is scheduled to arrive state side soon.

Upon sorting out the set-up I will follow-up with my critique of the quality and a...

http://www.fda.gov/downloads/medicaldevices/deviceregulationandguidance/guidancedocuments/ucm095304.pdf

(chair)