508,028 active members
2,543 visitors online
Register for free
Login

Search:

Type: Posts; User: dabularach

Search: Search took 0.00 seconds.

  1. They are from 2008

    They are from 2008
  2. Yes i did try to clear the alarm several times....

    Yes i did try to clear the alarm several times. It counts down from 15 and shuts off. Every time you press reset it resets the count but thats it
  3. Actually just got a response from haas. Here it...

    Actually just got a response from haas. Here it is


    Dave,

    Sounds like the battery is gone and hopefully the processor is ok. We would need to make a service call and if you want us to set it...
  4. Any suggestions what else to check? It is so...

    Any suggestions what else to check? It is so wierd that they ran and now after sitting the mill and lathe both have the same alarms. Is there fuses in the power supply i should check? I see to open...
  5. I just checked the voltage and it is at 241 volts...

    I just checked the voltage and it is at 241 volts between the 2 lines. The highest jumper goes from 221-240 and the transformer toward the bottom of the cabinet goes from 224-250
    Since the voltage...
  6. I will check the voltage that way. Can you think...

    I will check the voltage that way. Can you think of what else could cause this issue in both machines?
  7. I am heading back to look at the machines today....

    I am heading back to look at the machines today. So if the incoming voltage is good on both wires it must be something with the machines. Its just wierd that both have the same problem and they have...
  8. I just checked the voltage The 2 wires coming in...

    I just checked the voltage
    The 2 wires coming in are 119v each
    On the out side the wires on each end have 119 coming out but the middle wire has no power
  9. If the incoming voltage is slightly different now...

    If the incoming voltage is slightly different now than it was when last run could the jumper just need to be changed
    1 says up to 220 and the other says 220 and over if i remember correctly
  10. I will check later when i am there. The machine...

    I will check later when i am there. The machine has been run and was working fine. The thing that i find odd is that both the mill and lathe are both getting the same alarm and they had both been...
  11. I didnt see a low battery alarm but i know the...

    I didnt see a low battery alarm but i know the machine has been sitting for atleast 3 years and the breakers were off. If the battery died and lost all parameters could that be what is causing the...
  12. Do you mean a pic of how the wire comes into the...

    Do you mean a pic of how the wire comes into the machine or a pic of the meter while im checking it? I will be there tomorrow again. The voltage was near 120 sorry that was my error. I posted a pic...
  13. Do you mean a pic of how the wire comes into the...

    Do you mean a pic of how the wire comes into the machine or a pic of the meter while im checking it? I will be there tomorrow again. The voltage was near 120 sorry that was my error. I posted a pic...
  14. Haas mill and lathe overvolt power problems

    I turned the mill and lathe in my friends garage and i am getting overvolt alarms. These machines have been wired for years and never had this problem. When i check the voltage there are 2 wires...
  15. Re: Mach3 ports and pin set up need help please

    Thanks guys I just figured out the problem. I got the Y and the Z motor is working properly but the X was giving me a problem. I found one of the wires was loose for the X motor where it went into...
  16. Re: Mach3 ports and pin set up need help please

    Thank you
    I will try it when I get home
  17. Re: Mach3 ports and pin set up need help please

    257334

    Here is a pic i just took
  18. Re: Mach3 ports and pin set up need help please

    Do I have to contact the company who made the breakout board to find the correct pin asignment?
  19. Re: Mach3 ports and pin set up need help please

    Does the break out board determine what pins to use? I emailed the company that I bought it from so maybe they can help. The number on the drivers is DM542 made by act motor I purchased on ebay.The...
  20. Re: Mach3 ports and pin set up need help please

    one more thing,I set the Y axis to step pin 2 and direction pin 14 and the Y axis is working but the X and Z still are not working
  21. Mach3 ports and pin set up need help please

    Hello everyone.I had my router running last year and a few months ago I was trying to get another motor working as a 4th axis and I ended up changing the input for the step and dir for all 3 axis.I...
  22. Star SB-16 type D programming questions

    I am new to swiss type machines and the person who gave me a "Crash course" to this machine uses G120 for the coordinate system. Other people I have spoken to use G50. Is there a difference or...
Results 1 to 22 of 22