508,030 active members
2,415 visitors online
Register for free
Login

Search:

Type: Posts; User: Andriy77

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    244

    Re: ST30Y next gen control question

    This setting was removed to prevent possible crash during restart program. It is recommended to use other tools, like subprogram.
  2. axial test bar for BMT65 HAAS tool turret

    Advise, please, axial test bar for BMT65 HAAS tool turret. I found only BMT55 Test Bar -32mm (WTO) ...
  3. Replies
    1
    Views
    674

    Re: HAAS SL20T 236 alarm

    Do you resolve the problem?
  4. Replies
    1
    Views
    278

    Oil leak inside column of VM-2

    There is so much oil on the spindle motor inside column VM-2, I can not find where it come from - oil around Tool Reliese Piston, on the motor and fan. Air line has not additional oil filter, but it...
  5. Replies
    9
    Views
    1,511

    Re: High load on spindle EC400

    We have higher spindle load on HAAS ST-20, 10-12% at 1000 rpm, 20-22 % at 2500 rpm. I have checked belt, tension, encoder belt, it's OK. Where is noise from the spindle motor pulley, it seems bearing...
  6. Replies
    3
    Views
    1,074

    Re: new HAAS St-15 LOUD!?

    Yes, it's extremely loud.
  7. Replies
    9
    Views
    1,352

    Re: Heidenhain TNC 151 Display unreadable

    It was successful?
  8. Replies
    12
    Views
    2,965

    Re: HAAS ST30 Turret Alignment Procedure

    One more question: is possible to compensate backlash on X-Axis of ST-40?
  9. Replies
    12
    Views
    2,965

    Re: HAAS ST30 Turret Alignment Procedure

    To make this I need disassemble machine almost completely(( In addition it's not small (ST-40)
  10. Replies
    12
    Views
    2,965

    Re: HAAS ST30 Turret Alignment Procedure

    Yes, but it is 300 or so mm long, and when I measuring in different places of Z-Axis, I determine different deviation. Is it possible to measure straightness of linear guides on all length?
  11. Replies
    12
    Views
    2,965

    Re: HAAS ST30 Turret Alignment Procedure

    How to check straitness of linear guides of this machine? The spindle centerline is not parallel to wedge motion on Z-axis in some places, I suppose the linear guides are not straight.
  12. Thread: Renishaw

    by Andriy77
    Replies
    4
    Views
    605

    Renishaw

    Is it possible to use (and calibrate) Renishaw OMP-40 without OTS toll setter?
  13. Replies
    3
    Views
    682

    Re: alignment of Z axis

    The problem was in wrong measurements. Z-axis column is OK:)
  14. Replies
    3
    Views
    682

    alignment of Z axis

    How to make alignment of squareness of Z axis motion to X and Y axis on VF-3 machine? physically?
  15. Replies
    3
    Views
    762

    Re: spindle rotate during G83 canned cycle

    Problem was in Parameter 315 bit 1 NO SPIND CAN CYCLE
  16. Replies
    5
    Views
    1,699

    Re: VF-5/50 alarm 235 - SPINDLE Z FAULT

    I going to change encoder, but, interesting, generally it works OK, alarm appears when I turned spindle by hand in one direction, and then in opposite direction((
  17. Replies
    2
    Views
    528

    Poll: Gear box oil consumption

    How frequenly LOWGEAR BOX ALARM is appears in HAAS mills?
  18. Replies
    5
    Views
    1,699

    Re: VF-5/50 alarm 235 - SPINDLE Z FAULT

    I just check connections and connectors itself.
  19. Replies
    5
    Views
    1,699

    Re: VF-5/50 alarm 235 - SPINDLE Z FAULT

    I am not sure, because here http://www.cnczone.com/forums/showthread.php?36624-Alarm%20235%20Spindle%20Z%20Fault Alarm appears again, after new encoder was installed:confused:
  20. Replies
    2
    Views
    863

    Re: press brake can't find reference point

    Problem was in Y2 measuring scale..
  21. Replies
    5
    Views
    1,699

    VF-5/50 alarm 235 - SPINDLE Z FAULT

    It is intermittent alarm 235 SPINDLE Z FAULT on VF-5/50. Usually during program run no problem, but when run spindle in MDI or MAnual mode CW, and then another direction, even by hand, appears Alarm...
  22. Replies
    7
    Views
    581

    Re: Alarm 1001 during probing, VM-2

    Thanks all for help,
    I have TS27R, but I loaded mistakenly program for wireless probe. I changed program, and now probe works correct. Wired probe always "open", wireless are closed after probing.
  23. Replies
    7
    Views
    581

    Re: Alarm 1001 during probing, VM-2

    I tried to reload few versions of macro programs, but it doesn't help. Periodically appears alarm PROBE OPEN, when start probing.
  24. Replies
    7
    Views
    581

    Re: Alarm 1001 during probing, VM-2

    Alarm OTS swith off failure
  25. Replies
    7
    Views
    581

    Alarm 1001 during probing, VM-2

    At the end of probe calibration I get alarm 1001. Program works OK, but at the end, instead message PROGRAM END, I can see RUNNING, and then alarm 1001. May be problem with macros? How to fix it?
Results 1 to 25 of 28
Page 1 of 2 1 2