584,817 active members*
4,810 visitors online*
Register for free
Login

Search:

Type: Posts; User: gwood

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    171

    Re: Arrow 500 A2100 coolant pump

    File attached: 91203813B-STD-Coolant-Excerpts.bmp

    If you need more help; Bill Oehler (Fives Hebron Tech Support) can sell you prints or give you part numbers for the Solid State Output Chip....
  2. Replies
    4
    Views
    171

    Re: Arrow 500 A2100 coolant pump

    Please provide:
    Machine Serial Number: 70xx-Y0x-xxxx
    Model Type (USA machines): i.e. Exx, ERO, ERD, EKK etc... or Year of Manufacture from separate Plate below Serial Plate (for Europe and rest of...
  3. Replies
    4
    Views
    174

    Re: Falcon 200 turret won't align

    Here are documents for the BSA-200 turret. Macouser in Charlotte, NC was the distributor and service for these in the past.
    Hopefully you can figure something out and do not have to deal with them....
  4. Replies
    4
    Views
    174

    Re: Falcon 200 turret won't align

    You'll need to take a photo of the Duplomatic plate riveted to the tailstock (Centerline) of the Turret.
    It has the model number and serial number on it. I could be a Mechanical or Servo turret...
  5. Replies
    8
    Views
    421

    Re: Arrow 500 power cuts out

    I'm Not seeing a RED fault light and do not know what is happening to the Z-Slide at the time the LEDs go off except for a loud clunk heard.
    Is that the Z-Axis or the Electrical contactors in the...
  6. Re: Assistance needed backing up BIOS and parameters before machine move.

    SPGTech

    Machine Model ERO-B with Linear Electric Tool Changer Slide (Must be phased properly to advance to the spindle with Z-Axis all the way up at Alignment point)

    612632270003 Assy, Dual TX...
  7. Re: Need info converting Arrow 500 from CAT40 to BT40.

    Kwirk,
    Regarding the ANSI CAT 40 Toolholder versus the BT 40 Toolholder

    Reference Only:
    https://www.kemmler-shop.de/en/jis-b-6339-mas-403-bt-iso-7388-2/technical-information/...
  8. Replies
    8
    Views
    1,443

    Re: Arrow 750 has no power on the PSR 4/5 250-7500

    Search the Cincinnati forum for VFS5 and BDS5 posts. There are several handshakes and pieces that need to work to power the bus contactor on with no faults.
    Bill Oehler can work with you on the...
  9. Re: Need info converting Arrow 500 from CAT40 to BT40.

    CAT 40 used a blue gripper with different dimensions than the BT-40; BT 40 is a BLACK gripper different dimensions than the CAT-40.
    Tool Change height is different due to dimensional differences....
  10. Re: Need info converting Arrow 500 from CAT40 to BT40.

    Riveted to the outside of electrical cabinet door.
  11. Re: Need info converting Arrow 500 from CAT40 to BT40.

    Need a new spindle and tool fingers. CAT is better, you can orient a boring bar, or back-facing tool.
    Did you get a photo of the serial plate yet?
  12. Re: Assistance needed backing up BIOS and parameters before machine move.

    The Kollmorgen Drives were design to run on WYE power and do NOT like an unbalanced leg as found in DELTA.
    That's why they were sold with DELTA to WYE transformers.
    Still though get us that...
  13. Re: Assistance needed backing up BIOS and parameters before machine move.

    SPGTech, Please provide :
    Machine Serial Number: 70xxA0xyyyy ?

    Model Type: ie: ERO, EKK ???

    Control Diagrams: 9120xxxxYxx

    The 400V really bothers me on your plate; let find out what you...
  14. Re: Assistance needed backing up BIOS and parameters before machine move.

    I've added to Maverick's excellent suggestions:
    Arrow, Saber, Lancer with A2100 CNC & Kollmorgen BSD5 Spindle Drive -Shipping and Storage Ideas

    The factory used separate shipping brackets for X &...
  15. Replies
    36
    Views
    2,166

    Re: Squareness error compensation

    It your choice; but I would bet it is mechanical alignments, or leveling.
  16. Replies
    36
    Views
    2,166

    Re: Squareness error compensation

    Kwirk,
    Attached: 91204316-001A_EKK_Rel4x_Config.pdf (354.9 KB) Page # 2 & # 5 (Thermal Comp)
    Your Spindle (61264424A 8k STD Torque) or 10K with Spindle Cooler
    Attached:...
  17. Replies
    36
    Views
    2,166

    Re: Squareness error compensation

    Kwirk, There are two thermocouples; one on the Side of the column near the toolchanger assy., the other inside the spindle carrier down on the inside where the Spindle assembly bolts in.
    The Spindle...
  18. Re: ACRAMATIC 2100 SIEMENS - CONVENTIONAL SERVO DIAGNOSTIC FAILED

    Chivo,
    Attached (34242290A02_F2-Setup_Phoenix.PDF) Bios Setting for WSCPU Assembly.
    Please set these up with the Hard drive power unplugged.
    Restart the BIOS and verify. Save and exit; power down...
  19. Re: ACRAMATIC 2100 SIEMENS - CONVENTIONAL SERVO DIAGNOSTIC FAILED

    Chivo, What is the 3-424-xxxxAyy part number of the WSCP Assembly; so that I can send you settings?
  20. Re: Seeking C Axis Programming Help On Cincinnati Milacron 1210 Lathe w/850sx Control

    See PDF attached

    Also Face Contour Diamond PGM (Text)

    :010000G00G63G98G70X4.5-[M15]-[M40]Z10-[M16]-[M41]
    N010(MSG,MILL DIAMOND, T07 .5"DIA. ENDMILL)
    N020G92S4000.
    N030M26T7
    N040G0Z1.2-.7400...
  21. Re: ACRAMATIC 2100 SIEMENS - CONVENTIONAL SERVO DIAGNOSTIC FAILED

    Chivo, Document (DP-Profi-Master_A2100.pdf) attached.
    Looks like everyone is talking properly to the DP Profibus Master A2100 Card; something to do with RTCPU, or WSCPU Bios Settings.
    Did you test...
  22. Re: ACRAMATIC 2100 SIEMENS - CONVENTIONAL SERVO DIAGNOSTIC FAILED

    Chivo, I have written detail troubleshooting for the AL40-33 for Conventional CMHD I/o; but you have the profibus I/O instead.
    Can you post a picture of the Alarm? I do know that bad BIOS can cause...
  23. Re: ACRAMATIC 2100 SIEMENS - CONVENTIONAL SERVO DIAGNOSTIC FAILED

    Look at these two other files; one off the internet.
    What J1-5 slot is your Profibus card in? should be J4 next to RTCPU
  24. Replies
    1
    Views
    259

    Re: Cincinnati Arrow BDS5 Info Needed

    People do not understand that the VFS5 user variables and program are stored on RAM (CMOS memory) that is in a Dallas Real-Time Clock Chip with an INTERNAL battery embedded inside the Chip package....
  25. Re: ACRAMATIC 2100 SIEMENS - CONVENTIONAL SERVO DIAGNOSTIC FAILED

    See Attached file
  26. Re: Hawk 150, acramatic, servo motor rapids like mad on startup

    Are the drives BDS4, Vector-Star, or Siemens? What release Software shows in the Service page.
    The details make a large difference.
    SN 7051-A0x-yyyy ?
    Model type Exx; or year of manufacture below...
  27. Replies
    36
    Views
    2,166

    Re: Squareness error compensation

    The tests I provide instructions for on the end of the ball-screw take less than 15 minutes;
    spend your time looking for bad thrust bearings; or ball-screws that have lost their preloads.
  28. Replies
    36
    Views
    2,166

    Re: Squareness error compensation

    normally I prefer .012mm / 300mm (.0005" / 12" inches). If it is out more in X, than Y this would cause what you see.
    Also with scales you cannot check backlash since the scale is trying to hold the...
  29. Re: cincinnati hawk lathe how Convert the controller to inch

    A2100 Programming Modes: (Inch / Metric) ETC...
    Select > MORE>> > Service > Type the "service" password; hit enter and "Commit Changes". Level will display as SERVICE
    Select > MORE>> > System...
  30. Replies
    8
    Views
    421

    Re: Arrow 500 power cuts out

    Does this happen with the spindle turned off in a warm-up program? There should be an alarm on an AXIS Drive at the time of the fault.
    You may need to film it in slow-motion to figure it out.
    Your...
Results 1 to 30 of 283
Page 1 of 10 1 2 3 4