I hope it was that simple.
But it is at 100% at JOG tab.
Anywhere else?
Type: Posts; User: cjchands
I hope it was that simple.
But it is at 100% at JOG tab.
Anywhere else?
I have done several set up for MACH3 milling machine.
I am aware of config at motor tuning (velocity, acceleration, step per)
However... when I run the JOG mode..the movement is slow.
When...
I had the same problem. Are both your mouse/keyboards USB socket.
Change to those pin sockets type..or get adapters.
Should solve problem. IRQ conflict when spindle is turned on with inverter.
Looking for Retired Instructor to teach MACH3/Pc-based in Thailand!
We are opening up PC-based CNC making teaching courses in Thailand
and looking for assistance in Teaching Mach 3 or other PC...
Thanks Al
very clear explanation.
But I am wondering why can't the logic contact be connected? it is just the contact open/close?
I think you are right.
I am using those LOGIC for the contact VFD, not the load itself. I thought it could be used similarly to the normal relay.
Al,
I was pretty confident that should work too.
I connect the 2 SSR to FWD/REV/COM on the inverter to drive spindle CW/CCW.
Normal relay works. Perhaps just bad solid state relay?
Hello Guys.
I have this 2 brand new Solid State relays
(Salsar, SSR-10DA)
SSR Relay (SSR-10DA) - China Solid state relay,ssr,relays in Relay & Contactor
which I am currently use to close NO...
Too parameter page is all
0 00000000000000000
:(
Fanuc 11M...Is there a way to get Tool change Parameter if losing one?
I just recently got this SHODA NCB-193C CNC 3 axis with 16 ATC.
X/Y/Z and spindles work ok.
But nothing in Parameter for...
TYVM all for helpful comments.
Jeff
Oh by the way,
How do you recommend wiring 25 pins (Fanuc controller) to 9 pins (PC)?
Thank you soooo much.
Jeff
Hello.
I just brought CNC machines.
One with Fanuc 11M controller, another with 6T controller.
Since i don't have any CAM program.
Can anyone please advise where to get G-CODE transfer program...
I set up NEW COMPUTER today..
Brand new FORMAT, new WINDOW.
Install MACH 3 and check that parallel port address show up as
3F8
378
Like other computer....MACH 3 default should be set up at...
Hi guys.
I am very new to ARTCAM pro.
I want to cut simple 2D text using 1.5mm End mill.
My picture show that every time I use the
TOOLPATH (2D clearance).
I get these little offset that I...
Hello guys.
I done work with Mastercam previously..but very new with ARTCAM.
We just brought a copy of ARTCAM Pro version 8, but information is kinda ovewhelming.
Is there any basic tutorial so we...
NEWBIE Question: ENGRAVING FOAM vs. WOOD.
Hello.
I am new to Engraving Artwork (only done with METALworking).
So I am currious if anyone can point me to the cutting speed (RPM)
and Feedrate on...
Yeah..what was I thinking..thank you for pointing that out.
Just an update..
I brought new PCI breakout board....setting the 2nd parallel port and it work fine!!
But what actually happen was:
My breakout to stepper Drive was wiring in a way that I need...
Beat me...
I tuned it on today. And the tuning motor curve came back.
Nothing new install...nothing deleted.
The only thing that I did change was the wiring from Breakout board (step/direction)...
Thank you
I wasn't aware there is such a thing as 3V parallel port. Was assuming everything is 5V and either my wiring is bad so there is a drop in voltage.
I'll change it to different PCI board,...
First of all, thanks for detail explanation.
I follow your advice, Here are 2 scenarios:
According to your reference..I do not get above 4V in either LOW active off/on?
What should be my...
This has happened to me few times now..
I installed the new program.
I go to config -> tuning...and you can see trapezoid graph for tuning.
Few days later..
You can change values for step,...
This problem has occurred to me randomly as sometimes Stepping motors would run by itself when MACH 3 has not yet command any move (No JOG/ No Auto/etc..).
I suspect that the cause came from...
I don't know weather it is the noise or something else, but there is a problem now when I connect Parallel port to the breakout board and MACH 3 is on.
X-Axis motor would rotate tiny bit at a time....
Hi Al,
You are right!! It is R-C Network.
The part is RG1676-24 (1000V, 10W)
http://www.galco.com/techdoc/elcu/rg1676-16_app.pdf
I guess it is use for Back EMF in case switching FWD/REV right...
Hi,
I see that there are 3 capacitors connect to Magnetic Relay in parallel with R-S, S-T, T-R terminals.
The unit is for turning spindle motor clockwise or counter clockwise thru the hand switch....
What is the typical output voltage coming out from Parallel port as I get random voltages range from 1.6-3.0V (no breakout board….directly measuring from the port)?
My understanding is TTL low is...
Hello guys.
I got the machine working fine but Rapid is very slow.
I have P4 2.5Ghz.
Set Mach 3 at maximum 45000Hz.
In the Configuration page, I can crank velocity up to max at 1150.
Obviously,...