Search:

Why workshops have to buy the old machines? If the workshop has enough work for a new machine, then new machine to be purchased. If there is not enough work, then it is better to find someone who can...

One way or another you still need indicate spindle for run out. It will be very wise to do so. It all depends on your tolerance. If you can indicate on drill shank will be much better. Your spot must...

279668
JUST EXAMPLE, TRY LEARN FROM IT.
Parts ejection not for your machine, and T0700 !!!!!!

I did review your program, program is out of order, there is better way to do this. no offense.279666
First finish the sub routine then, start new part.

G810 MISSING $2

would you post the program,
just before you apporach with the sub enter G23 this code will shut off your parameter for sub spindle stroke and G22 will enable parameter.

you cannot change tool, while sub over the part.Take Sub back home G28W0, or move it away from the face of the part till you find, where you can change it next tool, W-3. then you will have to sync...

What is material size? If material size is over or 1/4 use L.H. cut off. That will give you ex. .500 or more.
It is parameter,"good parameter".

partially finished patr on l20, and have mills finish the rest.
this is nothing but headache

stop wandering, get rid of the job.

one time i had problem with "hold button", it was sticky, check that, or any other button

MAKE CHANGES IF YOU NEEDED

Mill .190 cross hole T1200 USE Y-Z PLANE

M80 S3=3000
T1200(1/8, END MILL)
(MAKE 1 PASS)
(SET RAD AT R.0625, SET P AT 0)
G50 W-.3937
G0 X.6 Z.25 Y0 C0 T12

You can turn this part however you like it, but if you going to turn inconel waspaloy, hexoloy... or other hard materials it will not work. I can tell you that much. Insert will not make 5 parts....

What material? i will do it this way
;I will rough x.125 than
finish turn x.125 with same tool x.25,
x.360 all the way to next x.125
then bring sub forward and do not let go part.

you may be...

That is unusual, MC DATA controls end point of c/off and P.PINT that is only for X. using MC DATA page. What do you have under DIA in PREPARATION PAGE for T1300 and for all tools.

A rotary guide bush rotates together with a work piece and holds the work piece for axial (z) sliding. A stationary guide bush remains stationary and holds a work piece and does not rotated, if you...

No offense, my man your program needs some kind of order. you have to many M98, i do not think you can do last part to.
make it simple, K-16E does not need any more M5 M18 for live tools. I see you...

you don`t have to use M140 and M141 for every single i.d. or turning in position t21,t22,t23 tool. set tools correctly. if you want do this, G0 Z-.2 after drilling or boring or turning.

DEFA

make bushing i.d. .156 o.d. bushing or collet size, make it out of brass
use test indicator .0001
put it all in the bushing or collet
tighten, test indicator can not be loose
call your tool to...

You can make it any way. i use shim 1/8 for station 11, just to run a way from wide of c/o. Copy program, load machine change what you like. Get her running. You will not have any alarms.

056330 (P#191825-0030)
$1
G99M6M9
M52
M118G113
M87M97
G50X-.01Z.527
G0X.625Z-.05

T1400(TURN R.0155 )

M98H1L5(L-LOOP SOMETHING) Can be use under $1 too, like this.

M5
M58S3=3500G98
G50W-.59
T0800((HOLE PATTERN-HOLES A LONG "Z" AND 3 HOLE A ROUND O.D. ))
G0X.6Z.3T08
M18C0.
M98H1L5

Thx.

Ask

DAMP YUOR PROGRAM OUT OF MACHINE, LOAD THIS ONE. YOU WILL FIND ERROR
$1
O5555
(T0202-FRONT-TURN R.015)
(T0303-B-T G.INSERT W.047/R.0025)
(T0100-C/O W.059 R.000)
/M52
M9M6M97M87
M118G113...

O5555( )
$1
G99M6M9
G50Z.617
G50S4000Q1000
M52
M118G113
M87M97
G0X1.1Z-.05
M3S1=3000

http://db.tt/fSxnAQXe
sv32

material is swelling-stretching:
turning to fast
drilling to fast - tool gets hot, do not make tools and material hot
--------------
concentricity:
check your bushing for run out. use test...

post drawing let us see it at least similar to it.

mastercam does not support swiss machine posts.