584,866 active members*
5,228 visitors online*
Register for free
Login

Search:

Type: Posts; User: mujkance

Search: Search took 0.00 seconds.

  1. Re: Gildemeister CT40 PLC, Eltropilot EPL2, Data backup/reload

    Hello Russell,

    you can contact me on:
    [email protected]

    Best regards,
    Samir
  2. Re: Gildemeister CTX400 Serie 2 - Spindle cannot turn!

    Hi,

    probably you have problem with you spindle amplifier.
    How do you clamp the chuck? I have Gildemeister CTX 520 linear and I can't to clamp chuck. If I clamp it, than I can't unclamp. How to...
  3. Thread: 180I control

    by mujkance
    Replies
    9
    Views
    2,245

    Re: 180I control

    Hello guys!

    I didn't find any other similar thread, so I will text you here.
    I have one machine with FANUC 180i MA control and it has 5 axes. Now I want to switch off 5th axis because we don't...
  4. Re: Gildemeister CT40 PLC, Eltropilot EPL2, Data backup/reload

    Hello guys!

    I have Gildemeister GAC100 machine withe ElektroPilot controll. Can anyone explain me how to input program into machine?

    I can do output program from machine to my laptop, with...
  5. Replies
    9
    Views
    3,649

    Re: Anyone used sub-spindle as tailstock?

    Hello guys

    I need your quick help, please... I have Okuma LT10-M lathe, and have a problem with W axis CAL command. When WB axis comes to main spindle to grab the piece, I want to stop the machine...
  6. Replies
    5
    Views
    1,126

    Re: technical question

    Hmm...

    If you have problem only when you connect spindle servo drive, and you told me earlier that servo drive unit was on repair and they didn't find nothing wrong on it and your spindle motor is...
  7. Replies
    5
    Views
    1,126

    Re: technical question

    Hello Daniel

    I think you have X and Z, not Y axis, but that isn't important at this point.

    I didn't understand you very well... You have checked spindle servo drive and everything is good with...
  8. Replies
    4
    Views
    2,412

    Re: Okuma OSP U10M Spindle control problem

    Hello ungie,

    I didn't worked at this type of machine, but I have experience with an Alfing machine and I have the same problem.

    At the end I found out that problem was with clamping of tool...
  9. Replies
    34
    Views
    24,406

    Re: VAC II spindle drive fix notes

    Hello kenny

    I think alarm 11 can be caused by faulty IGBT modul. Do you know how to check it?

    If you don't know, follow this. You don't need to pull out VACIII drive. Disconnect motor cables...
  10. Replies
    3
    Views
    1,169

    Re: OKUMA OSP 5020L G112 ALARM 660

    Hello

    Do you have manual? Maybe there is some description that may help you...

    If you have some additional informations (how alarm occured etc.), maybe I can help you.

    Best regards, ...
  11. Replies
    1
    Views
    2,450

    Re: Okuma LB15 1-1 CPU Alarm (Cycle over)

    Hello!

    I suppose you are done with this long time ago. :)

    Do you have a table with addresses of cards? I have similar problem with my OSP U100-L, alarm is 1-3, access address = FC000000
    ...
  12. Replies
    17
    Views
    7,720

    Re: OKUMA system bus error (SBER)

    Hello people!

    Can anyone help me with my Okuma LT10-M, OSP U100-L control.

    I have similar alarm.

    1-3 CPU-ALARM BUS ERROR (CYCLE OVER)
    BUS ERROR STATUS (SBER, SBPAR, CYO, 0, PRT, DIA, LOP,...
Results 1 to 12 of 12