Hi
I understand this thread is one year old, but have you solved your problem?
I have a SKT200 2007 Oi with the same alarm.
When i try to MDI ex: M03S1000 it clicks and pops the same Al.
rgds
Type: Posts; User: CNCELOS
Hi
I understand this thread is one year old, but have you solved your problem?
I have a SKT200 2007 Oi with the same alarm.
When i try to MDI ex: M03S1000 it clicks and pops the same Al.
rgds
Hi
This da*** machine has decidE to give me a hard time.
I try do comand with the MDI ( M03S1000) to test and it gives a click and pops the following:
n.2032
Al-32 -CENTER POSITION NG
Problem solved.
It was a phase situation. I have read somewhere some situation
similar and decide to try and change one of the phases.
rgds
Now other problem come up.
No hydraulics, nothing on the gauges. even on the pump gauge.
The motor appears to be working, the block on top its hot, but no fluid on the hoses.
Level seems fine....
This Problem solved. I forgot about the STAND BY button (idiot)
I am new to this thing.
Small update.
Sorted/fixed the problems of the fans so far.
There was one last fan in the Power Supply Module in the internal PCB board that was stuck.
It is necessary to remove the wiring and...
Hi
I will appreciate some help please.
I will try to detail below.
Got hold of a used 2007/ Hyundai kia SKT200 / fanuc 0i from a broker in Germany.
Dealer told me machine was fully working on...
Hello
Great news so far.
The machine powered up and the Ethernet is working as well.
The bios settings did it.
I made a part and not noticeable issues on machining.
How ever the monitor once go...
Email is the usarname with the @gmail.com
Humm..
I have tried to request a add as a contact you.
Hello Bloke.
I have pm you.
If you did not received pls say so.
rgds
Valter
Driving everyday 100km to accomplish nothing gets very depressing.
Unfortunately i could not get the network to work. It was working before flawlessly.
All equipment is on the same subnet/ip...
Maybe my router its not working correctly? I notice that the power button is flashing.
But i can connect to him correctly.
Tommorow i will bring the laptop and see if i can connect to the machine....
But now i got into a different problem.
My previous WiFi connection to the machine via a WiFi router its not working.
The ISA card gets recognized by the system.
I can access the Network...
Got it to work
Many Thanks Bloke I owe you good.
The HDD Settings were the correct ones. It booted up nicely.
Here is a link to the machine doing the warm up.
...
please forgive my ignorance...
Once i power on machine what is the correct procedure to access cmos on this machine on the control?
Its like a computer? Pressing F? on power on?
Unfortunately...
Graphic card out and screen already show some activity...
But it is showing me the disk boot failure.
Has it it something to do with the battery or did i connect the HDD the wrong way?
I believe...
Ok, will try that.
I had disconnect the hdd hoping that if it was it at least would post some msg, but nope.
I wasnt sure if i could leave the Graphic card out.
Here the photos where is the board and how it is connected via wire.
Hope it helps on something.
I have just re-seated both the peak card and the graphic card with no success.
I have cleaned all the contacts, either on the boards and the slots with contact cleaner.
The problem persists.
I...
Hello Burgs
Yes Ethernet his way better if you have the hardware installed.
I think you need to have the ultinet option...
Assuming you have...
what i did was i setup a wifi connection between PC...
I was meant to replace the capacitor on the graphic Card not the PEAK CPU.
That is why i was wondering if a similar (not necessary the same model)could be viable?
Somehow i have a felling that...
Hello Blake
The control seems to beep, with regularity. However it not very noticeble with the fans working. Like beep for little time and the pauses them beeps. Not those intermittent fast beeps....
Hello Bloke, i was prying you would help. Many thanks
Did not notice because of the fans noise.
Will try your suggestion and also take the cpu board out and clean the contacts.Using the static...
I have read some post on the internet however i am a bit dense on electronic/electrics
Could someone point me out how to trace the problem, please.
I can check it but need guidance.
Machine:...